There are several places to define catalog configuration values:
SYSCATxx, LOADxx, IGGCATxx, and the MODIFY CATALOG command. Table
Table 1 shows which attributes you can specify
in each. However, for complete information, see the following:
The system applies the parameters in IGGCATxx, LOADxx, and SYSCATxx
in the following order:
- Parmlib member IGGCATxx, if specified, takes the highest priority,
followed by...
- Parmlib member LOADxx followed by...
- SYSCATxx member of SYS1.NUCLEUS followed by...
- System defined defaults
IGGCATxx overlaps extensively with the MODIFY CATALOG command,
as you can see in
Table 1. The system applies
IGGCATxx values at IPL time as well as at the restart of the Catalog
Address Space, while command configuration changes are temporary,
lasting only until the next IPL.
Note: Some of these attributes
are specified by subparameters of the CONTENTION, ECSHR, ENABLE, or
DISABLE parameters of the MODIFY CATALOG command.
Table 1. Intersection of SYSCATxx, LOADxx,
IGGCATxx, and MODIFY CATALOG commandKeyword |
Attribute |
IGGCATxx |
LOADxx |
SYSCATxx |
MODIFY CATALOG |
---|
|
Master catalog name |
No |
Yes |
Yes |
No |
|
Master catalog type |
No |
Yes |
Yes |
No |
|
Master catalog volume |
No |
Yes |
Yes |
No |
ALIASLEVEL |
Number of data set name qualifiers to be used
in the multilevel alias facility catalog search |
Yes |
Yes |
Yes |
Yes |
ALLOCLCK |
Contention detection settings for ALLOCLCK resource |
Yes |
No |
No |
CONTENTION |
AUTOADD |
AUTOADD function |
Yes |
Yes |
Yes |
ECSHR |
CATMAX |
Maximum number of catalogs that can be opened
concurrently in CAS |
Yes |
No |
No |
Yes |
DELFORCEWNG |
Warning message IDC1997I or IDC1998I |
Yes |
No |
No |
ENABLE | DISABLE |
DELRECOVWNG |
Warning message IDC1999I |
Yes |
No |
No |
ENABLE | DISABLE |
DSNCHECK |
Syntax checking on names being added to a catalog |
Yes |
No |
No |
ENABLE | DISABLE |
DUMPOFF DUMPON
|
CAS dynamic dumping |
Yes |
No |
No |
Yes |
EXTENDEDALIAS |
Ability to create extension records for user
catalog aliases on the current system |
Yes |
No |
No |
ENABLE | DISABLE |
GDGFIFOENABLE |
FIFO ordering of GDG |
Yes |
No |
No |
No |
NOTIFYEXTENT |
Monitor percentage of the maximum extents possible
for a currently allocated catalog |
Yes |
No |
No |
Yes |
SYMREC |
Creation of SYMREC records |
Yes |
No |
No |
ENABLE | DISABLE |
SYS%OFF SYS%ON
|
SYS% conversion |
Yes |
No |
Yes |
Yes |
SYSIGGV2 |
Contention detection settings for SYSIGGV2 resource |
Yes |
No |
No |
CONTENTION |
SYSZTIOT |
Contention detection settings for SYSZTIOT resource |
Yes |
No |
No |
CONTENTION |
SYSZVVDS |
Contention detection settings for SYSZVVDS resource |
Yes |
No |
No |
CONTENTION |
TAPEHLQ |
Tape volume catalog high level qualifier |
Yes |
Yes |
Yes |
No |
TASKMAX |
Maximum number of concurrent user service tasks |
Yes |
No |
No |
Yes |
TASKMIN |
CAS service task lower limit (minimum number
of CAS service tasks or requests) |
Yes |
Yes |
No |
Yes |
TASKTABLESIZE |
CAS task table size |
Yes |
No |
Yes |
No |
UPDTFAIL |
Warning message IEC390I |
Yes |
No |
No |
ENABLE | DISABLE |
VVDSSPACE |
Catalog volume data set space allocation |
Yes |
No |
No |
Yes |
VVRCHECK |
Enhanced VVR checking on VVDS I/O |
Yes |
No |
No |
ENABLE | DISABLE |
If you wish to suppress the IEA347A message that
prompts for the master catalog name at IPL time, you must use the
LOADxx member. Note that this means that the system uses the default
TASKTABLESIZE value. If you want a larger TASKTABLESIZE , you must
specify it in the SYSCATxx parmlib member and you cannot supress the
IPL prompt.