PCIe 380 MB Cache Dual - x4 3 Gb SAS RAID Adapter (FC 5805; CCIN 574E)

Learn about the specifications and operating system requirements for the feature code (FC) 5805 adapter.

Overview

The PCI Express (PCIe) 380 MB Cache Dual - x4 3 Gb SAS RAID Adapter supports the attachment of Serial attached SCSI (SAS) disk and SAS solid-state drives by using a pair of mini SAS 4x connectors. The 5805 has a 380 MB write cache and a concurrently replaceable cache battery pack. The adapter must always be installed in pairs and is always to be used in a high availability, multi-initiator RAID configuration using two adapters in dual-controller mode. Two 5805 adapters provide mirrored write-cache data and mirrored RAID parity footprints between the adapters. If the 5805 pairing is broken, then write cache is disabled.

Important: See the SAS RAID controllers for AIX®, SAS RAID controllers for IBM® i, or SAS RAID controllers for Linux topics for more information and important considerations for multi-initiator and high availability or dual storage IOA configurations

The 5805 supports SAS small form factor (SFF) disk drives located in a PCIe 12X I/O Drawer or SAS disk drives located in an EXP 12S Disk Drawer. It can also be connected to the internal disk drives in the system unit using the appropriate split disk backplane feature and cabling.

The adapter is a 3.3 V, PCI-e x8 bootable SAS adapter that supports RAID levels 0, 5, 6, and 10.

With adequate cabling and configuration, multiple wide ports are used to provide redundant paths to each dual port SAS drive or solid-state drive. The adapter manages SAS path redundancy and path switching in case a SAS failure occur.

The 5805 contains a LED ((C) in Figure 1) that flashes if the cache data is present. The cache-data present LED flashes when there is possible data in the cache on the adapter. If the cache data present LED is flashing, do not replace the cache battery pack. If replaced when the LED is flashing, the cache data is lost. See Figure 1 to locate the cache-data present LED on this adapter.

Attention: Do not attempt to replace the cache battery pack if the cache-data present LED on the card is flashing. The cache-data present LED indicates that there is possible data in the cache on the adapter. To prevent data loss, first make sure that the system has been shut down correctly. If the cache-data present LED is flashing, refer to one of the following topics before removing the cache battery pack.
Note: When configuring a raid array using the IBM toolkit and the FC5903 adapter for a system running Linux, the list of supported Direct Attach Storage Devices (DASD) is visible in the HMC only if you select the LVM configure option in the IBM toolkit.

The following figure shows the adapter.

Figure 1. PCIe Dual - x4 3 Gb SAS RAID Adapter
Graphic showing SAS RAID adapter and the cache-data present LED

Specifications

Item
Description
Adapter FRU number
46K4735 (Designed to comply with RoHS requirement.)
Battery FRU number
44V7597 (Designed to comply with RoHS requirement.)
I/O bus architecture
PCIe x8
Slot requirement
One PCIe x8 slot per adapter.
Adapters are installed in pairs.
Adapter pairs do not require to be in the same enclosure. For higher availability, place adapters in separate enclosures. See the PCI adapter placement for placement rules.
Cables
When you attach 5886 EXP 12S Disk Drawer, at least one of the following SAS (X) cables must be used: 3661, 3662 or 3663.
SAS device attachment requires specific cables that are provided with the subsystem or device features being attached. Special cabling is required for multi-initiator and high availability configurations. See Serial attached SCSI cable planning.
Voltage
3.3 V
Form factor
Short
Maximum number
For details about the maximum number of adapters that are supported, see PCIe adapter placement rules and slot priorities and select the system you are working on.
Attributes
  • 48 SAS disk dives supported when the adapter is configured with four 5886 EXP 12S Disk Drawers
  • 42 SAS disk drives supported when the adapter is configured with a 19-inch PCIe 12X I/O Drawer and two 5886 EXP 12S Disk Drawers (18 SFF disk drives plus up to 24 SAS disk drives)
  • SAS speed: 3 Gbps
  • SAS Serial-SCSI Protocol (SSP) and Serial Management Protocol (SMP) are supported
  • 380 MB of non-volatile fast write cache can increase disk subsystem performance
  • Dual controller supports mirrored-write cache data and mirrored-RAID parity footprints
  • Concurrent firmware update supported
  • Eight physical links from two mini SAS 4x connectors are provided
  • Concurrent replaceable cache battery pack
  • Removable media devices are not supported

For details about slot priorities and placement rules, see PCIe adapter placement rules and slot priorities and select the system you are working on.

Operating system or partition requirements

If you are installing a new feature, ensure that you have the software that is required to support the new feature and that you determine whether any prerequisites must be met for this feature and attaching devices. To check for the prerequisites, see IBM Prerequisite website.

The adapter is supported on the following versions of the operating systems, depending on the system you are using:
  • AIX:
    • AIX 7.1, or later
    • AIX Version 6.1, or later
  • Linux:
    • Red Hat Enterprise Linux Version 7, or later, with current maintenance updates available from Red Hat.
    • Red Hat Enterprise Linux Version 6.4, or later, with current maintenance updates available from Red Hat.
    • SUSE Linux Enterprise Server 10, Service Pack 3, or later
  • IBM i
    • IBM i Version 7.2 or later
    • IBM i Version 7.1, or later



Last updated: Thu, June 27, 2019