Licensed Internal Code installation error displays
Use the Licensed Internal Code installation error displays to determine what actions to take. For example, the system might be missing the load-source disk.
One of the following three displays might be shown if you chose option 1 (restore) on the install selection menu and the selected disk is not currently a load-source disk unit. In this case, the restore cannot be done. If the selected disk is the correct one to install to, return to the selection menu and choose the correct install option 2, 3, 4, or 5 to initialize the disk and perform an installation. If the selected disk is not the correct one, or if an existing load-source disk unit should have been found, follow the appropriate procedures to determine why the correct disk did not report in, or was not recognized.
If there is information about a missing disk (second or third of the following three displays), it indicates what the last load-source disk unit was on this system. If that disk still exists (it has not been removed or replaced), determine why it was not found. If that disk has been removed or replaced, then this is just informational and might not indicate an error.
Restore Licensed Internal Code
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The disk selected has not previously been a load source. The
restore of the Licensed Internal Code cannot be done.
Press Enter to return to the Install Licensed Internal Code
screen.
Restore Licensed Internal Code
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The load source disk could not be found (see disk information
below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The disk selected has not previously been a load source. The
restore of the Licensed Internal Code cannot be done.
Press Enter to return to the Install Licensed Internal Code
screen.
Restore Licensed Internal Code
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The load source disk and its mirrored pair could not be found
(see disk information below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
__________ ____ ___ ____ ____ ____
The disk selected has not previously been a load source. The
restore of the Licensed Internal Code cannot be done.
Press Enter to return to the Install Licensed Internal Code
screen.
The following display can be shown if you chose option 1 (restore) on the install selection menu, but the release level of the Licensed Internal Code on the install media cannot be restored over the current release level on disk. Verify that you have the correct install media (version/release/modification level). If the level is correct, then you must do an initialize and install to get the new Licensed Internal Code installed over the existing Licensed Internal Code on the disk.
Restore Licensed Internal Code
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The release level of the Licensed Internal Code on the distribution
media cannot be restored over the existing release level on the
selected disk.
Press Enter to return to the Install Licensed Internal Code
screen.
The following display can be shown if you chose option 1 (restore) on the install selection menu and the selected disk is currently a load-source disk unit, but the pertinent data on the disk cannot be read and, therefore, a restore cannot be done. You must do an initialize and installation to install the new Licensed Internal Code on this disk.
Restore Licensed Internal Code
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The selected disk cannot be read. The restore of the Licensed
Internal Code cannot be done.
Press Enter to return to the Install Licensed Internal Code
screen.
The following display can be shown if two load-source disk units are detected on your system. The best disk was selected for the restore or installation. The data about the other disk is informational so you can verify that the correct disk was selected. If the correct disk was not selected, follow the appropriate procedures to disable or remove the selected disk , so that the other disk is selected when you rerun the task.
Install Licensed Internal Code - Warning
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Warning:
Another load source disk has also been found on this system.
If you continue the restore or install, the disk listed
above will be used.
Additional load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Press Enter to continue the restore or install on the selected
disk.
The following display is shown if mirroring is active but one disk of the load source mirrored pair cannot be found. The restore or installation can still continue on the selected disk, but will not be mirrored until the missing disk becomes again active. You might want to follow the appropriate procedures to determine why one of the disks were not found.
Install Licensed Internal Code - Warning
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Warning:
The mirrored unit for this load source was not found (see
disk information below). The restore or install can continue
on the selected load source. The missing mirrored unit will
be suspended when the restore or install is complete.
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Press Enter to continue the restore or install on the selected
disk.
The following two displays are shown if the disk selected for the install to is not the same disk that was previously the load source on this system. If the missing disk should still exist (it has not been removed or replaced), determine why it was not found. If the disk was removed or replaced, this data is just informational and might not indicate an error.
Install Licensed Internal Code - Warning
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Warning:
The load source disk could not be found (see disk information
below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Press Enter to continue the initialize and install on the
selected disk.
Install Licensed Internal Code - Warning
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Warning:
The load source disk and its mirrored pair could not be found
(see disk information below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
__________ ____ ___ ____ ____ ____
Press Enter to continue the initialize and install on the
selected disk.
The following display is shown if mirroring is active and the active load-source disk unit cannot be found. One unit of the load source mirrored pair was found but is not currently active. You can install to it, but you will not be allowed to initial program load (IPL) past dedicated service tools (DST) with it. You might want to follow the appropriate procedures to determine why the active load-source disk unit cannot be found.
Install Licensed Internal Code - Warning
Disk selected to write the Licensed Internal Code to:
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Warning:
A load source disk could not be found (see disk information
below).
The disk selected to be the load source (see above) is
suspended. You can install to it and perform an IPL from it to
get to DST and perform disk diagnostics. However, you will not
be able to perform an IPL past DST with it.
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
Press Enter to continue the restore or install on the selected
disk.
- No valid, functional load-source disk unit exists on the system.
- No disk units can be made into load-source disk units.
If information is supplied about a missing disk (second and third of the three displays), it indicates what was the last load-source disk unit on this system. If that disk still exists (it has not been removed or replaced), then determine why it was not found. If that disk has been removed or replaced, then this data is just informational and might not be the reason for the error.
Install Licensed Internal Code - Error
Error:
A disk could not be selected to be the load source.
You can return to the dedicated service tools display and
run diagnostics to determine why a disk could not be
selected.
Correct the problem and install the Licensed Internal Code
again.
Press Enter to return to the dedicated service tools display.
Install Licensed Internal Code - Error
Error:
The load source disk could not be found (see disk information
below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
A disk could not be selected to be the load source.
You can return to the dedicated service tools display and
run diagnostics to determine why a disk could not be
selected.
Correct the problem and install the Licensed Internal Code
again.
Press Enter to return to the dedicated service tools display.
Install Licensed Internal Code - Error
Error:
The load source disk and its mirrored pair could not be found
(see disk information below).
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
__________ ____ ___ ____ ____ ____
A disk could not be selected to be the load source.
You can return to the dedicated service tools display and
run diagnostics to determine why a disk could not be
selected.
Correct the problem and install the Licensed Internal Code
again.
Press Enter to return to the dedicated service tools display.
One of the following two displays is shown if a disk is found, but it is not at a valid address to be the load source.
If there is information about a missing disk (the second display), it indicates what the last load-source disk unit was on this system. If that disk still exists (it has not been removed or replaced), determine why it was not found. If it has been removed or replaced, this is just informational and might not be the reason for the error.
Install Licensed Internal Code - Error
Error:
A disk was found, but it is not at a valid address to be the
load source device.
Selected disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The install cannot be done. Press Enter to return to the Dedicated
Service Tools display.
Install Licensed Internal Code - Error
Error:
A disk was found, but it is not at a valid address to be the
load source device.
Selected disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The following disk was a load source previously, but could not be
found.
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The install cannot be done. Press Enter to return to the Dedicated
Service Tools display.
The following display is shown if an existing load-source disk unit is found, but is not at a valid address to be the load source. If it was intentionally moved, determine why no other disk can be found to which to install. If this is the correct disk , determine why it is not at a valid address.
Install Licensed Internal Code - Error
Error:
The following disk was a load source previously, but it is not
currently at a valid address to be the load source device.
Selected disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The install cannot be done. Press Enter to return to the Dedicated
Service Tools display.
The following display is shown if an existing load-source disk unit was found and:
- Is not at a valid address to be the load source.
- Is one unit of a mirrored pair.
- Is currently not the active load source.
Information about the previously active load source is also listed. If this load source is still available to install to, use the appropriate procedures to determine why it cannot be found.
Install Licensed Internal Code - Error
Error:
The following disk was a load source, but it is not currently
active, and it is not at a valid address to be the load source
device.
Selected disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The following disk was the previously active load source, but it
could not be found.
Missing load source disk :
Serial Number Type Model I/O Bus Controller Device
__________ ____ ___ ____ ____ ____
The install cannot be done. Press Enter to return to the Dedicated
Service Tools display.