Explanation
[CF LOSSCONN RECOVERY MANAGEMENT IS IN PROGRESS]
[LARGER CFRM COUPLE DATA SET REQUIRED. FORMAT A NEW
CFRM USING AT LEAST THE FOLLOWING:
ITEM NAME(STR) NUMBER(str#)
ITEM NAME(CONNECT) NUMBER(conn#)]
[THE COUPLE DATA SET FOR CFRM SUPPORTS THE MAXIMUM NUMBER
OF STR RECORDS. totalstr STRUCTURE(S) MUST BE DELETED FROM THE POLICY
TO ACCOMMODATE STRUCTURES ALLOCATED IN THE COUPLING FACILITY.]
[totalstr STRUCTURE(S) MUST ALSO BE DELETED FROM THE POLICY
TO ACCOMMODATE STRUCTURES ALLOCATED IN THE COUPLING FACILTY.]
[THE REALLOCATE PROCESS IS IN PROGRESS.]
[THE REALLOCATE PROCESS IS STOPPING.]
CFNAME COUPLING FACILITY SITE
cfname type.mfg.plant.sequence sitename [ - RECOVERY SITE]
PARTITION: partition [SIDE: side ] CPCID: cpcid
[ALLOCATION NOT PERMITTED]
[MAINTENANCE MODE]
[POLICY CHANGE PENDING - DELETE]
[COUPLING FACILITY FAILED]
[COUPLING FACILITY IN CLEANUP]
[POPULATECF REBUILD IN PROGRESS]
[THE CFRM ACTIVE POLICY IS EMPTY]
A DISPLAY
XCF,CF command was entered to display summary information about the
coupling facilities defined in this sysplex. The system will repeat
the message text to report all coupling facilities.
If no coupling
facilities are displayed, then the trailer message shown above will
be displayed instead to explain the absence of coupling facility names.
If
the CFRM Couple Data Set needs to be reformatted, then a message will
be displayed before any coupling facility names are listed. This message
will specify the numbers to be used in reformatting the data set.
If the REALLOCATE process has been initiated, then a
message will be displayed before any structures are listed. This message
will indicate the current state of the REALLOCATE process. The REALLOCATE
process will be in progress if a SETXCF START,REALLOCATE operator
command has been issued. The REALLOCATE process will be stopping if
a SETXCF STOP,REALLOCATE operator command has been issued. Once started,
the REALLOCATE process will evaluate each allocated structure to determine
the need for activation of a pending policy and/or location adjustment
of instance(s) allocated in CF(s). REALLOCATE processing will end
either when all allocated structures have been evaluated with appropriate
action taken or when the REALLOCATE process was stopped and relocation
steps for the current target structure have finished.
In the
message text:
- hh.mm.ss
- The time in hours (00-23), minutes (00-59), and seconds (00-59)
for the DISPLAY XCF command.
- CF LOSSCONN RECOVERY MANAGEMENT IS IN PROGRESS
- A loss of connectivity to a coupling facility occurred that required
connector recovery.
- str#
- The STR number to be used in reformatting the CFRM Couple Data
Set. If the current number is adequate, then this line will not be
displayed.
- conn#
- The CONNECT number to be used in reformatting the CFRM Couple
Data Set. If the current number is adequate, then this line will not
be displayed.
- totalstr
- Total number of structures that should be deleted from the CFRM
active policy.
- THE REALLOCATE PROCESS IS IN PROGRESS.
- The REALLOCATE process is initiated by the SETXCF START,REALLOCATE
operator command. Once started, the REALLOCATE process examines each
allocated structure to determine whether the location of any instance
needs to be adjusted and/or a pending policy activated. The evaluation
process uses the XCF allocation algorithm which factors in the CFRM
active policy information and current set of active connections to
make the determination.
- THE REALLOCATE PROCESS IS STOPPING.
- The REALLOCATE process is stopped by the SETXCF STOP,REALLOCATE
operator command. Once stopped, the structure which is the current
target of the REALLOCATE process will complete the relocation steps
prior to ending the REALLOCATE process.
- COUPLING FACILITY
- The coupling facility which this system is able to use is identified
by the node descriptor. See mapping IXLYNDE. The format xxxxxx.xxx.xx.xxxxxxxxxxxx
gives the type, manufacturer ID, manufacturer plant ID, and sequence
number.
- cfname
- Name of coupling facility from the CFRM active policy
- type
- Node type (See ndetype in IXLYNDE).
- mfg
- Node manufacturer ID (See ndemfg in IXLYNDE).
- plant
- Node manufacturer plant ID (See ndeplant in IXLYNDE).
- sequence
- Node sequence number (See ndesequence in IXLYNDE).
- sitename
- The name of the site from the CFRM active policy. If the Recovery
Manager is active and the site is the recovery site, " - RECOVERY
SITE" will appear after the site name.
- partition
- Node LPAR partition number (See ndepartition in IXLYNDE).
- side
- The node PP/SI mode indicator and configuration code from the
IXLYNDE are used to determine the value for side.
Value and meaning are:
- SIDE: 0 means the coupling facility is on SIDE 0 of a partitionable
CPC.
- SIDE: 1 means the coupling facility is on SIDE 1 of a partitionable
CPC.
- blank means the coupling facility is in a non-partitionable CPC.
- cpcid
- Node Central Processor Complex (CPC) ID.
- ALLOCATION NOT PERMITTED
- Structure allocation is not permitted in the specified coupling
facility.
System action
The system continues processing.
Source
Cross System Coupling Facility (SCXCF)
Module
Routing code
Descriptor code