IEE844W

Explanation
text is: aaaaa:    bbbbbbbb
PSW:      cccccccc cccccccc cccccccc cccccccc
CR 3-4:   dddddddd   eeeeeeee
AR/GR 0-1: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      2-3: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      4-5: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      6-7: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      8-9: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      A-B: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      C-D: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg
      E-F: aaaaaaaa/gggggggg_gggggggg   aaaaaaaa/gggggggg_gggggggg

A
SLIP command requested that the system set a SLIP trap with an action
of wait.  The system found a match for this trap. The match is:
A program event recording (PER) event in which the unit of work
is not an enabled, unlocked task. Because the unit of work cannot
be stopped safely, the system performs the WAIT action immediately,
but not the remote actions specified.
An error event.

In the message text:
xxxx
The SLIP trap identifier specified on the SLIP command.
ACTION=WAIT
Indicates that when a match is found for the trap, the system
is to stop and display trap data in message IEE844W.
TYPE=yy
The system mode.
REMOTE ACTION{S} NOT PERFORMED
The SLIP command also specified the COND option of the REMOTE
keyword.
aaaaa      bbbbbbbb
Additional information based on the system mode indicated in TYPE=yy. System Mode (yy)
aaaaa:  
bbbbbbbb

RTM1
SDWA ADDR: 
The address of the system diagnostic work area (SDWA) associated
with the error.

RTM2
RTM2WA ADDR: 
The address of the recovery termination manager (RTM) 2 work
area (RTM2WA) associated with the error.

System Mode (yy)
aaaaa: 
bbbbbbbb

MEMTERM
ASCB ADDR: 
The address of the address space control block (ASCB) being
abnormally ended.

PER
PER INFO: 
The PERcode PER-address. code is
the type of PER event. address is the 8-byte
address where the PER event occurred.

PSW: cccccccc cccccccc cccccccc cccccccc
The 16-byte program status word (PSW) of
the event. If the SDWA indicates that the register and PSW information
is not valid, the message reads:  PSW: NOT AVAILABLE.
CR 3-4:  dddddddd eeeeeeee
The content of control registers 3 and 4. These registers contain
cross memory information. If the SDWA indicates that the register
and PSW information is not valid, the message reads:  CR 3-4: NOT
AVAILABLE.
GR n-n:  ffffffff…ffffffff
The content of the general registers. If the SDWA indicates that
the register and PSW information is not valid, the message reads: GR
0-F: NOT AVAILABLE.
AR n-n:  ffffffff…ffffffff
The content of the access registers at the time of the PER interrupt
or the error.  The content of these registers is provided only if
the processor was in AR mode.

System action
The system issues this message to display trap
data and enters a restartable wait state, as requested in the trap.

Operator response
Perform the actions requested by the system
programmer for this trap. Restart the system.
If the system
programmer requests, obtain a stand-alone dump. ReIPL the system.

System programmer response
Examine the message for information
about the event. To capture diagnostic data, the SLIP trap can request
an SVC dump, or, if necessary, ask the operator to obtain a stand-alone
dump. The system cannot be restarted if a stand-alone dump is written;
ask the operator to reIPL the system.

Source
SLIP

Module
IEAVTSL2

Routing code
1

Descriptor code
1

System Mode (`yy`)	`aaaaa`:	`bbbbbbbb`
RTM1	SDWA ADDR:	The address of the system diagnostic work area (SDWA) associated with the error.
RTM2	RTM2WA ADDR:	The address of the recovery termination manager (RTM) 2 work area (RTM2WA) associated with the error.

System Mode (`yy`)	`aaaaa`:	`bbbbbbbb`
MEMTERM	ASCB ADDR:	The address of the address space control block (ASCB) being abnormally ended.
PER	PER INFO:	The PER`code` PER-`address`. `code` is the type of PER event. `address` is the 8-byte address where the PER event occurred.