CBR1110I   OAM library status:

Explanation

TAPE      LIB  DEVICE    TOT  ONL  AVL   TOTAL   EMPTY  SCRTCH  ON OP    
LIBRARY   TYP  TYPE      DRV  DRV  DRV   SLOTS   SLOTS    VOLS           
tlibname  typ  tdevtype llll mmmm nnnn ooooooo ppppppp Sqqqqqqq  r  s   

OPTICAL  DEVICE   ATT USE AVL TOT EMP SCR PT DEV ON OP IO LIB   READ
LIBRARY  TYPE     DRV DRV DRV SLT SLT VOL    NUM       ST CMD   COUNT
olibname odevtype aaa bbb ccc ddd eee fff  g hhhh i  j  k lbcmd rdcnt
TAPE      LIB  DEVICE    TOT   ONL  AVL   TOTAL   EMPTY SCRTCH  ON OP
LIBRARY   TYP  TYPE      DRV   DRV  DRV   SLOTS   SLOTS   VOLS
tlibname  typ  tdevtype  1lll mmmm nnnn ooooooo ppppppp qqqqqq  r  s
The operator has entered one of the following commands: 
D SMS,LIBRARY(library-name),DETAIL
D SMS,LIBRARY(ALL),DETAIL
A display of OAM library status has been generated. When a library name is supplied, there is one data line describing the specified library; when ALL is supplied, there is one data line for each library in the configuration. If both optical and tape libraries have been defined in the SMS configuration, the sample display above will be generated. Otherwise, only the data for the library type defined will be generated.
For an optical library, the fields displayed in each data line of the multiline message are as follows:
olibname
Name of the optical library.
odevtype
Name of the library device type, as follows:
3995-111
3995 rewritable library, extension to 3995-131
3995-112
3995 write-once library, extension to 3995-132
3995-113
3995 multifunction library, extension to 3995-133
3995-131
3995 rewritable library and controller
3995-132
3995 write-once library and controller
3995-133
3995 multifunction library and controller
3995-C3A
3995 multifunction library controller
3995-C12
3995 multifunction library, extension to 3995-C32
3995-C16
3995 multifunction library, extension to 3995-C36
3995-C18
3995 multifunction library, extension to 3995-C38
3995-C32
3995 multifunction library, attaches to 3995-C3A
3995-C34
3995 multifunction library, attaches to 3995-C3A
3995-C36
3995 multifunction library, attaches to 3995-C3A
3995-C38
3995 multifunction library, attaches to 3995-C3A
aaa
The total number of optical drives defined to the optical library.
bbb
The number of usable optical drives (online, operational, and not pending offline).
ccc
The number of available optical drives (online, operational, not pending offline, and not currently in use).
ddd
The total number of storage slots in the optical library.
eee
The number of empty storage slots in the optical library.
fff
The number of scratch volumes in the optical library.
g
The active path to the optical library, as follows:
P
Primary
A
Alternate
blank
Pseudolibrary or 3995 library
hhhh
MVS device number of the active CTC or blank for pseudolibraries.
i
Optical library online status, as follows:
Y
Online
N
Offline
P
Pending offline
j
Optical library operational status, as follows:
Y
Operational
N
Not operational
k
Optical library input/output station operational status, as follows:
Y
Operational
N
Not operational
*
An error occurred while trying to get the status
blank
Library not attached or library has no I/O station
lbcmd
For 3995 libraries, REMAP indicates that a REMAP of the library is in progress, RMPND indicates that a REMAP is pending for the library, and AUDIT indicates that a full library audit is being processed. If not REMAP, RMPND, or AUDIT, this field contains the library command most recently sent to this optical library.
rdcnt
The number of read requests waiting or in progress for optical volumes that are resident in this optical library.
If a specific optical library is requested in the LIBRARY command, the additional data lines will appear as follows: 
--------------------------------------------
DEFAULT PSEUDO LIB: def-plib-name
DEFAULT MEDIA TYPE: def-mediatype
XCF MEMBER NAME: member-name
--------------------------------------------

The value of def-plib-name in the data line is the name of the pseudolibrary that will be assigned to any volume that is ejected from this library if that volume does not already have a pseudolibrary associated with it. Def-plib-name is specified on the 3995 Library Define panel in ISMF.

The value of def-mediatype in the data line indicates what media types can be entered into the optical library and what media types can be written to if they already reside in the library. Def-mediatype is specified on the 3995 Library Define panel in ISMF.

The value of member-name in the data line is the XCF member name associated with the instance of OAM where this library is currently online. If the library is not online to any instance of OAM in the OAMplex, this field will contain blanks. If this instance of OAM is not currently part of an OAMplex, this field will contain ‘N/A’.

For a tape library, the fields displayed in the data line of the multiline message are as follows:
tlibname
The name of the tape library.
typ
The tape library type, as follows:
AL
Automated tape library dataserver
ML
Manual tape library
VCL
Peer-to-Peer VTS or Virtualization Engine Composite Library
VDL
Peer-to-Peer VTS or Virtualization Engine Distributed Library
VL
Virtual tape server
UNK
Unable to obtain the tape library type from the hardware
tdevtype
For an automated tape library, the tape library device type is displayed as DDDD-MMM where DDDD is the device type of the library and MMM is the model. For a manual tape library MANUAL is displayed.
llll
The total number of tape drives, known to the current system, residing in the tape library.
mmmm
The number of tape drives, known to the current system and residing in the tape library, that are online.
nnnn
The number of tape drives, known to the current system and residing in the tape library, that are online and not allocated.
ooooooo
The total number of storage slots in the tape library. For a library that resides in a 3584 tape library, the storage slot count is associated with a particular logical library. For other tape libraries, the storage slot count reflects the number of storage slots in the entire physical library. Also, starting from Release 1.5 of the TS7740 (3957-V06), when the TS7740 is installed in a 3584 tape library (with ALMS), the distributed library no longer surfaces the physical slot information and instead surfaces virtual slot information.

For a TS7680, this count displays the number of logical volumes that can be defined to the library.

ppppppp
Total number of empty slots in the tape library dataserver. For a TS7680, this count displays the number of logical volumes that can still be defined to the library.
qqqqqq
The total number of eligible scratch volumes in the tape library.
r
The tape library online status, as follows:
Y
Online
N
Offline
P
Pending offline
s
The tape library operational status, as follows:
Y
Operational
N
Not operational
If a specific tape library is requested in the DISPLAY SMS,LIBRARY command, additional data lines appear containing information about that library, as follows: 
-------------------------------------------------
MEDIA       SCRATCH       SCRATCH       SCRATCH
TYPE          COUNT     THRESHOLD      CATEGORY
MEDIAxx    vvvvvvvv        xxxxxx          wwww
-------------------------------------------------
LIBRARY ID: libid
CACHE PERCENTAGE USED: xxx
OPERATIONAL STATE:{AUTOMATED | PAUSED | MANUAL MODE}
ERROR CATEGORY SCRATCH COUNT:          aeaeae
SCRATCH STACKED VOLUME COUNT:          afafaf
PRIVATE STACKED VOLUME COUNT:          agagag
CORRUPTED TOKEN VOLUME COUNT:          ahahah
HIGH CAPACITY INPUT STATION CAPACITY:  tttttt
HIGH CAPACITY OUTPUT STATION CAPACITY: uuuuuu
-------------------------------------------------
status lines

The media type line is repeated for the applicable media types.

The media type, scratch count, scratch threshold, and scratch category lines are displayed only for media that have a threshold value or a scratch count greater than zero.

For a VTS composite or distributed library, the appropriate composite or distributed line will be displayed mapping their association.

The library ID line displays the five-character ID assigned to the library.

The cache percentage used is displayed only for a TS7720 (3957-VEx) distributed library or for a TS7680 (3958-DE2); it indicates what percentage of cache the library has utilized.

The error category will display the total number of scratch volumes that have a software error associated with them. Scratch volumes in this category will still have a use attribute of scratch; however, they are not eligible to be mounted.

The scratch stacked volume count will only be displayed for a virtual tape server (VTS) library; it indicates the number of available physical scratch volumes. For a Peer-to-Peer VTS subsystem, this information can be obtained by displaying the distributed libraries associated with the composite library. This count is suppressed if the library being displayed is a TS7720 (3957-VEx).

The private stacked volume count will only be displayed for a virtual tape server (VTS) library; it indicates the number of physical stacked private volumes. For a Peer-to-Peer VTS subsystem, this information can be obtained by displaying the distributed libraries associated with the composite library. This count is suppressed if the library being displayed is a TS7720 (3957-VEx).

The corrupted token volume count will only be displayed for a Peer-to-Peer virtual tape server (VTS) library and indicates the number of volumes in the corrupted token category. For a Peer-to-Peer VTS subsystem, this information can be obtained by displaying the composite library. For corrective action, contact your hardware service representative.

For a VTS composite library, the operational state that is returned to the host is determined by examining the states of the underlying distributed libraries, with much of the other status (for instance, I/O station-related status) being provided from the designated user interface library. Also, since all of the drives and volumes are defined to and associated with the composite library, the display of a distributed library will show that, from a host perspective, there are no volumes and drives associated with that library. The distributed libraries should be displayed for an accurate picture of the total and empty slot counts (the slot counts associated with the composite library are zero).

The high capacity input and output station lines will only be displayed for an automated tape library dataserver and only if the station has been configured.

For an automated tape library data server, additional status lines may appear containing one or more of the following messages:
  • Operation degraded due to unavailable hardware resource.
  • Safety enclosure interlock open.
  • Vision system not operational.
  • Library manager offline.
  • Operator intervention required.
  • Library manager check 1 condition.
  • All storage slots full.
  • Out of cleaner volumes.
  • Dual write disabled.
  • Environmental alert.
  • Library manager switchover in progress.
  • Copy operations disabled.
  • VTS operations degraded.
  • Immediate Mode Copy operations deferred.
  • Service preparation occurring in distributed library library-name.
  • Service preparation occurring.
  • All convenience input stations empty.
  • All convenience output stations empty.
  • All convenience output stations full.
  • {Bulk Input/Output | Output} {Configured | Not configured}.
  • High capacity output station full.
  • {Input | Output} door is open.
  • Convenience I/O station installed.
  • Convenience I/O station in {Input | Output | Import mode}.
  • Convenience I/O station {Empty | Full}.
  • Single cell output facility in use for eject.
  • Host initiated import in process.
  • Host initiated export in process.
  • Library initiated single volume import in process.
  • Library is out of empty stacked volumes.
  • Library has insufficient resources to continue mount processing.
  • Library supports import/export.
  • Library supports outboard policy management.
  • Limited cache free space – warning state.
  • Out of cache resources – critical state.
  • Forced pause occurred.
  • Grid links degraded.
  • Library supports logical WORM.
  • Copy operations disabled by operator command.
  • Synchronous mode copy operations deferred.
  • Library enabled for scratch allocation assistance.

Source

Object Access Method (OAM)

Routing Code

-

Descriptor Code

5,8,9

Parent topic: CBR messages