AMD033I
I/O ERROR ON dev CMD = cmd STATUS = stat COND = err

Explanation

During processing of a stand-alone dump, a permanent I/O error occurred.

In the message text:
dev
The device number of the device on which the error occurred.
CMD=cmd
The channel command that was being run.
STATUS=stat
The status bits, if applicable, or NONE, if not applicable.
COND=err
The type of error for which the stand-alone dump program was attempting recovery; it is one of the following:
  • For channel path errors:
    • CHAINING CHECK
    • CHANNEL CONTROL CHECK
    • CHANNEL DATA CHECK
    • INCORRECT LENGTH
    • INTERFACE CONTROL CHECK
    • PCI
    • CHANNEL PROGRAM CHECK
    • CHANNEL PROTECTION CHECK
  • For device or control unit errors:
    • ATTENTION
    • BUSY
    • CONTROL UNIT END
    • STATUS MODIFIER
    • UNIT EXCEPTION
  • For direct access device errors:
    • BUFFERED LOG FULL
    • BUS OUT PARITY
    • COMMAND REJECT
    • DATA CHECK
    • END OF CYLINDER
    • ENVIRONMENTAL DATA PRESENT
    • EQU CK
    • FILE PROTECTED
    • INTERVENTION REQUIRED
    • INVALID TRACK FORMAT
    • MISSING ADDR MARKER
    • NO RECORD FOUND
    • OPERATION INCOMPLETE
    • DEFERRED ACCESS
    • PERM ERROR
    • SEEK CK
    • TRACK COND CK
  • For 3990 Storage Control errors:
    • OPERATION TERMINATED
    • SUBSYSTEM PROCESSING ERROR
    • CACHING TERMINATED
    • NON-RETENTIVE ACCESS NOT AUTHORIZED
    • TRACK FORMAT INCORRECT
    • CACHING REINITIATED
    • NON-VOLATILE STORAGE TERMINATED
    • VOLUME IS FAILED DUPLEX
    • VOLUME STATUS INDEFINITE
  • For type device errors:
    • BUS OUT PARITY
    • COMMAND REJECT
    • DATA CHECK
    • DATA CONVERTER CK
    • EQU CK
    • FILE PROTECTED
    • INTERVENTION REQUIRED
    • LOAD POINT
    • NOT CAPABLE
    • DEFERRED ACCESS
    • PE ID BURST CK
  • For paging storage device errors:
    • BASE DEVICE UNAVAILABLE
    • DISABLED INTERFACE
    • MICROCODE LOGIC ERROR
    • STORAGE DIRECTOR COMMUNICATION FAILED
    • SUBSYSTEM STORAGE AVAILABILITY THRESHOLD CROSSED
    • SUBSYSTEM STORAGE EQUIPMENT CHECK
    • SUBSYSTEM STORAGE MUST BE INITIALIZED
    • SUBSYSTEM STORAGE IS UNUSABLE
    • TRACK FORMAT NOT SUPPORTED FOR PAGING
    • WRITE INHIBITED
  • For 3480 Magnetic Tape Subsystem errors:
    • BACKWARD AT BEGINNING OF
    • TAPE
    • BLOCK ID SEQUENCING
    • CONTROL UNIT ERROR
    • CONTROL UNIT ERP FAILED
    • DATA CHECK READ
    • DATA CHECK (READ OPPOSITE)
    • DATA SECURITY ERASE FAILURE
    • DEFERRED CONDITION CODE 3 -
    • DEVICE IS NOT OPERATIONAL
    • DEGRADED MODE ERRORS
    • DEMARK DATA BUFFER
    • DRIVE ASSIGNED ELSEWHERE
    • DRIVE EQUIPMENT CHECK
    • DRIVE NOT ONLINE
    • DRIVE PATCH LOAD FAILURE
    • DRIVE RESET BY OPERATOR
    • FORMAT INCOMPATIBLE — 3480-2 XF FORMAT
    • FUNCTION INCOMPATIBLE
    • LOCATE BLOCK UNSUCCESSFUL
    • LOAD ASSISTANCE
    • LOAD DISPLAY TIMEOUT
    • LOAD FAILURE
    • LOG AND RETRY
    • MANUAL UNLOAD
    • NOT READY
    • PATH EQUIPMENT CHECK
    • PERMANENT EQUIPMENT CHECK
    • PHYSICAL END OF TAPE
    • READ BUFFERED LOG (EOV)
    • READ BUFFERED LOG (OVERFLOW)
    • TAPE DRIVE/CONTROL UNIT INCOMPATIBLE
    • TAPE LENGTH INCOMPATIBLE
    • TAPE LENGTH VIOLATION
    • TAPE LENGTH ERROR
    • TAPE VOID
    • VOLUME REMOVED BY OPERATOR
    • WRITE DATA CHECK
    • WRITE ID MARK CHECK
  • For 3490 magnetic tape subsystem errors:
    • DATA STREAMING ERROR
    • CHECK ONE ERROR
    • RESETTING EVENT
    • GLOBAL COMMAND INTERCEPT
    • CHANNEL INTERFACE RECOVERY (TEMPORARY) ERROR
    • CHANNEL INTERFACE RECOVERY (PERMANENT) ERROR
    • CHANNEL PROTOCOL ERROR
    • ATTENTION INTERCEPT ERROR
    • FUNCTION INCOMPATIBLE
  • For magnetic tape devices:
    • LOST SENSE DATA
    • DRIVE ASSIGNED ELSEWHERE
    • ALLEGIANCE RESET
    • COMMAND REJECT
    • CONFIGURATION ERROR
    • PROTECTION EXCEPTION
    • WRITE PROTECTED
    • WRITE LENGTH ERROR
    • READ-ONLY FORMAT
    • BEGINNING OF PARTITION
    • END OF PARTITION
    • END OF DATA ENCOUNTERED
    • BLOCK NOT FOUND
    • READY THE DEVICE
    • READY THE LOADER
    • WRITE ERROR DETECTED
    • ERASE ERROR DETECTED
    • FORMATTING ERROR DETECTED
    • READ ERROR DETECTED
    • UNSUPPORTED FORMAT
    • VOLUME IS NOT FORMATTED
    • POSITIONING LOST
    • READ LENGTH ERROR
    • UNSUPPORTED MEDIUM
    • MEDIUM LENGTH ERROR
    • MEDIUM MANUALLY UNLOADED
    • RELOAD THE TAPE
    • UNLOAD THE TAPE
    • EQUIPMENT CHECK
    • BUS OUT CHECK
    • CHANNEL PROTOCOL ERROR
    • INTERFACE ERROR
    • OVERRUN
    • HALT SIGNAL
    • DEVICE FENCED
    • DEVICE-PATH FENCED
    • MEDIA INFORMATION MESSAGE
    • I/O SUBSYSTEM SIM
    • DEVICE SIM
    Note: If an error occurs such that message AMD033I is required and the 3590 message code in sense byte 6 does not apply to any of the above conditions, then message AMD033I is issued with COND=DEVICE MESSAGE CODE IS IN SENSE BYTE 6.
  • For special errors:
    • ERROR IN ERROR RECOVERY - While attempting to recover from the error indicated by the status and sense bytes, a second error occurred from which recovery was impossible.
    • ERROR ON SENSE COMMAND - An error occurred while the system was reading the sense bytes.
    • UNKNOWN - The error indicated by the status and sense bytes is unexpected. No recovery exists.
    • UNUSED - The stand-alone dump program generated an incorrect message.

System action

The stand-alone dump program does not complete the I/O operation successfully. The dump program also issue message AMD034I. If the I/O error is a permanent error on the output device, stand-alone dump issues message AMD098A.

Operator response

If the error is WRITE INHIBITED and message AMD014A follows, turn the write inhibit switch of the device to the write position. If message AMD098A is issued, see the operator response for AMD098A.

For all other errors, fix the problem, if possible.

Source

Stand-alone dump (SADMP)

Module

AMDSADER, AMDSATER, AMDSAT80, AMDSAIOI, AMDSABRA

Routing code

-

Descriptor code

-

Parent topic: AMD messages