RECEIVE (MRO)

Receive data on an MRO conversation.

Read syntax diagramSkip visual syntax diagram
RECEIVE (MRO)

>>-RECEIVE--+---------------+--+-INTO(data-area)-+-------------->
            '-SESSION(name)-'  '-SET(ptr-ref)----'   

>--+-LENGTH(data-area)--+--+------------------------+----------->
   '-FLENGTH(data-area)-'  +-MAXLENGTH(data-value)--+   
                           '-MAXFLENGTH(data-value)-'   

>--+------------+--+-------------+-----------------------------><
   '-NOTRUNCATE-'  '-STATE(cvda)-'   

Conditions: EOC, INBFMH, INVREQ, LENGERR, NOTALLOC, TERMERR

 

Description

RECEIVE receives data from the conversation partner in an MRO conversation.

Options

FLENGTH(data-area)
A fullword alternative to LENGTH.
INTO(data-area)
specifies the receiving field for the data read from the terminal or logical unit, or the application target area receiving the data from the application program connected to the other end of the current conversation.

If you specify the INTO option, but omit the MAXLENGTH option, the argument for the LENGTH option must be a data area that specifies the maximum length that the program accepts. If the value specified is less than zero, zero is assumed.

If the length of the data exceeds the value specified, but the NOTRUNCATE option is not specified, the data is truncated to that value and the LENGERR condition occurs. When the data has been received, the data area for the LENGTH option is set to the original length of the data.

LENGTH(data-area)
specifies the length, as a halfword binary value, of the data transmitted.

If you specify the INTO option, but omit the MAXLENGTH option, the argument must be a data area that specifies the maximum length that the program accepts. If the value specified is less than zero, zero is assumed.

If the length of the data exceeds the value specified, but the NOTRUNCATE option is not specified, the data is truncated to that value and the LENGERR condition occurs. When the data has been received, the data area is set to the original length of the data.

If you specify the SET option, the argument must be a data area. When the data has been received, the data area is set to the length of the data.

For a description of a safe upper limit, see LENGTH options in CICS commands.

MAXFLENGTH(data-value)
A fullword alternative to MAXLENGTH.
MAXLENGTH(data-value)
specifies the maximum amount (halfword binary value) of data that CICS® is to recover. If INTO is specified, MAXLENGTH overrides the use of LENGTH as an input to CICS. If SET is specified, MAXLENGTH provides a way for the program to limit the amount of data it receives at one time.

If the value specified is less than zero, zero is assumed.

If the length of data exceeds the value specified and the NOTRUNCATE option is not present, the data is truncated to that value and the LENGERR condition occurs. The data area specified in the LENGTH option is set to the original length of data.

If the length of data exceeds the value specified and the NOTRUNCATE option is present, CICS retains the remaining data and uses it to satisfy subsequent RECEIVE commands. The data area specified in the LENGTH option is set to the length of data returned.

If this option is omitted, the value indicated in the LENGTH option is assumed.

NOTRUNCATE
specifies that, when the data available exceeds the length requested, the remaining data is not to be discarded but is to be retained for retrieval by subsequent RECEIVE commands.
SESSION(name)
specifies the symbolic identifier (1–4 characters) of a session TCTTE. This option specifies the alternate facility to be used. If this option is omitted, the principal facility for the task is used.
SET(ptr-ref)
specifies a pointer reference that is to be set to the address of data received from the conversation partner in an MRO conversation. The pointer reference is valid until the next receive command or the end of task.

If DATALOCATION(ANY) is associated with the application program, the address of the data can be above or below the 16MB line.

If DATALOCATION(BELOW) is associated with the application program, and the data resides above the 16MB line, the data is copied below the 16MB line, and the address of this copy is returned.

If TASKDATAKEY(USER) is specified for the running task, and storage protection is active, the data returned is in a user-key. If TASKDATAKEY(CICS) is specified and storage protection is active, the data returned is in a CICS-key.

If you specify the SET option, the argument for the LENGTH option must be a data area. When the data has been received, the data area is set to the length of the data.

STATE(cvda)
gets the state of the current conversation. The cvda values returned by CICS are:
  • ALLOCATED
  • FREE
  • PENDFREE
  • RECEIVE
  • ROLLBACK
  • SEND
  • SYNCFREE
  • SYNCRECEIVE
  • SYNCSEND

Conditions

The following conditions can occur in combination with others. CICS checks for these conditions in the order:
  1. INBFMH
  2. EOC
If more than one occurs, only the first is passed to the application program. EIBRCODE, however, is set to indicate all the conditions that occurred.
06 EOC
occurs when a request/response unit (RU) is received with the end-of-chain indicator set. Field EIBEOC also contains this indicator.

Default action: ignore the condition.

07 INBFMH
occurs if a request/response unit (RU) contains a function management header (FMH). Field EIBFMH contains this indicator and it should be used in preference to INBFMH. The IGNORE CONDITION command can be used to ignore the condition.

Default action: terminate the task abnormally.

16 INVREQ
RESP2 values:
200
A distributed program link server application specified the function-shipping session (its principal facility) on the CONVID option.

Default action: terminate the task abnormally.

22 LENGERR
occurs if data is discarded by CICS because its length exceeds the maximum the program accepts and the NOTRUNCATE option is not specified.

Default action: terminate the task abnormally.

61 NOTALLOC
occurs if the facility specified in the command is not owned by the application.

Default action: terminate the task abnormally.

81 TERMERR
occurs for a terminal-related error, such as a session failure. This condition applies to z/OS® Communications Server-connected terminals only.

A CANCEL TASK request by a user node error program (NEP) may cause this condition if the task has an outstanding terminal control request active when the node abnormal condition program handles the session error.

Default action: terminate the task abnormally with abend code ATNI.



dfhp4_receivemro.html | Timestamp icon Last updated: Thursday, 27 June 2019