PCIe LP 2-Port 1GbE SX Adapter (FC 5274; CCIN 5768)
Learn about features, requirements, and specifications for the feature code (FC) 5274 adapter.
The PCIe LP 2-Port 1GbE SX Adapter provides two 1 Gbps (1000 Base-SX) full-duplex Ethernet LAN connections. The adapter interfaces to the system through a PCIe bus. It is PCIe x4 capable and conforms to the PCIe 1.0a standard. The adapter connects to a network using a standard shortwave multimode optical cable that conforms to the IEEE 802.3z standard. The adapter supports distances of 260 m (853.01 feet) for 62.5 micron Multi Mode Fiber (MMF) and 550 m (1804.46 feet) for 50.0 micron MMF. AIX® Network Installation Management (NIM) boot capability is supported with this adapter.
- Supports interrupt moderation to deliver increased performance while significantly reducing processor utilization
- Supports dual port operation in almost any PCIe slot, except x1
- Supports auto-negotiation, full-duplex only
- Supports integrated media-access control (MAC) and physical layer (PHY)
- Supports Fast EtherChannel (FEC) with the existing software
- Supports gigabit EtherChannel (GEC) with the existing software
- Supports IEEE 802.3ad (Link Aggregation control protocol)
- Supports IEEE 802.1Q VLANs
- Supports IEEE 802.3 z, ab, u, x flow control support
- Supports IEEE 802.1p
- Supports IEEE 802.3ab for TX
- Supports TCP checksum offload transmission control protocol (TCP), user datagram protocol (UDP), Internet Protocol (IP) for IPv4 and IPv6
- Supports TCP segmentation or large send offload
- Supports EEPROM-SPI and single EEPROM
- Supports interrupt levels INTA and MSI
- Hardware certifications FCC B, UL, CE, VCCI, BSMI, CTICK, MIC
- Network Controller (MAC) Intel 82571EB
- Compliant with European Union Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Adapter specifications
- Item
- Description
- FRU number
- 10N6846*
- *Designed to comply with RoHS requirement
- I/O bus architecture
- PCI Express V1.0a compliant
- Bus width x4 lane PCI Express, operable in x4, x8, x16 slots
- Bus speed (x4, encoded rate) 10 Gbps unidirectional; 20 Gbps bidirectional
- Busmaster
- Yes
- Maximum number
- For details about the maximum number of adapters that are supported, see PCIe adapter placement rules and slot priorities and select the system you are working on.
- Adapter size
- PCIe short form
- Connector information
- Two fiber optic ports, LC connector
- LED status indicators for link activity and speed
- Wrap plug FRU number
- 12R9314 (SFP+ SR wrap plug)Note: These wrap plugs are not included with the card. 12R9314 (FC ECW0)IBM®.
- Cabling
- Optional LC-SC converter cables are available:
- LC-SC 62.5 micron converter cable, part number 12R9322, FC 2459.
- LC-SC 50 micron use converter cable, part number 12R9321, FC 2456.
Adapter LED states
The LEDs on the adapter provide information about the adapter's operation status. The LEDs are visible through the adapter's mounting bracket. Figure 1 shows the location of the LEDs. Table 1 describes the different LED states and what those states indicate. The following figure shows the adapter.
- 1
- LEDs
- 2
- Multimode Fiber LC receptacles
| LED | Description |
|---|---|
| Off | No link (The absence of a link could indicate a bad cable, bad connector, or a configuration mismatch.) |
| Green | Good link, no activity |
| Flashing Green | Good link, data activity |
Operating system or partition requirements
If you are installing a new feature, ensure that you have the software that is required to support the new feature and that you determine whether any prerequisites must be met for this feature and attaching devices. To check for the prerequisites, see IBM Prerequisite website.
- AIX
- AIX 7.1, Technology Level 3, Service Pack 2, or later
- AIX 6.1, Technology Level 8, Service Pack 3, or later
- AIX Version 5.3, Technology Level 12, or later
- Linux
- Red Hat Enterprise Linux Version 7, or later, with current maintenance updates available from Red Hat.
- Red Hat Enterprise Linux Version 6.4, or later, with current maintenance updates available from Red Hat.
- SUSE Linux Enterprise Server 11, Service Pack 1, or later, with current maintenance updates available from SUSE.
- For support details, see the Linux Alert website.
- The latest version of the device driver or iprutils can be downloaded from the IBM Service and Productivity Tools website.
- IBM i
- IBM i Version 7.2 or later
- IBM i Version 7.1, or later
Preparing for installation
If you are installing the operating system at this time, install the adapter before you install the operating system. See Installing the adapter for instructions.
If you are installing only the device driver for this adapter, install the device driver software before you install the adapter. See Installing the device driver software for instructions.
If you already have one of these adapters installed and working with your AIX operating system and you are preparing to install additional adapters, the device driver is already installed and you must not reinstall the device drive.
Verify you hardware requirements
- A wrap plug for the multimode fiber connector, if you are running the total diagnostics package
- Shortwave (850 nm) 50/62.5 micron multimode fiber network attachment
The following table indicates the allowable cable lengths from the adapter to the gigabit Ethernet switch, including patch cables.
| Cable type | Physical connector type | Maximum range |
|---|---|---|
| 62.5 m MMF | LC | 260 meters (853.01 feet) |
| 50 m MMF | LC | 550 meters (1804.46 feet) |
Verify your software requirements
The adapter is supported on operating systems shown in Operating system or partition requirements. Ensure that your operating system supports this adapter before you install it. Contact service and support if you need assistance.
Gather tools and documentation
- The adapter
- The operating system documentation
- The system unit documentation for removing and replacing features
- The PCI adapter placement documentation
- A flat-blade screwdriver
- The AIX base operating system CD, which includes the device driver, or the AIX device driver CD
Installing the device driver software
This section explains how to install device driver software. The device driver is provided for the AIX 5L™ operating system on the AIX base operating system CD, which includes the device driver, or the AIX device driver CD
To install device driver software, do the following steps:
- Log in to the system unit as root user.
- Insert the media containing the device driver software
(for example, the CD) into the media device.
If your system does not have a CD-ROM drive, refer to your system documentation for completing a Network Installation Management (NIM) installation.
- Type the following System Management Interface Tool (SMIT) fast path command: smit devinst
- Press Enter. The Install Additional Device Software window highlights the INPUT device / directory for software option.
- Type the name of the input device that you are using, or press F4 to select the input device from a list.
- Press Enter. The Install Additional Device Software window highlights the SOFTWARE to install option.
- Press F4 to select List.
- Type / to display the Find window.
- Type the device package name devices.pciex.14103f03.
- Press Enter. The system finds and highlights this device driver software.
- Press F7 to select the highlighted device driver software.
- Press Enter. The INSTALL ADDITIONAL DEVICE SOFTWARE window displays. The entry fields are automatically updated.
- Press Enter to accept the information. The ARE YOU SURE window displays.
- Press Enter to accept the information. The COMMAND
STATUS window displays.
- The message RUNNING is highlighted to indicate that the installation and configuration command is in progress.
- When RUNNING changes to OK, scroll to the bottom of the page and locate the installation summary.
- After a successful installation, SUCCESS displays in the Result column of the installation summary at the bottom of the page.
- Remove the installation media from the drive.
- Press F10 to exit SMIT.
Verify the AIX software installation
To verify that the device driver for the adapter is installed, do the following steps:
- If necessary, log in as root user.
- Type lslpp -l devices.pciex.14103f03.rte and
press Enter.
If the device driver is installed, the following is an example of the data that is displayed.
Fileset Level State Description Path: /usr/lib/objrepos devices.pciex.14103f03.rte 5.x.0.0 COMMITTED PCIe LP 2-Port 1GbE SX Adapter - Confirm that the devices.pciex.14103f03.rte filesets are installed. If no data displays, try reinstalling the driver.
Installing the adapter
This section explains how to install the adapter. If you are installing the operating system at this time, install the adapter before you install the operating system. If the operating system is already installed and you must install the device driver for this adapter, install the device driver software before you install the adapter.
To install the adapter, follow these steps:
- Determine the PCIe slot in which to place the adapter.
The adapter has an x4 PCIe connector and can be placed in a x4, x8, or x16 slot. See the PCI adapter placement for information about the PCIe slots on your system unit.
- Install the adapter by using the instructions in the system unit service guide.
Connecting to an Ethernet network
Refer to your local procedures for information about connecting the adapter to your Ethernet network.
- Only one type of network can be attached to the adapter at one time.
- If your switch has an SC receptacle, you need an LC-SC converter cable.
- You must configure an IP network interface to enable the adapter to detect the link and illuminate the link LED.
To connect the adapter to a multimode fiber network, do the following steps:
- Insert the male fiber LC connector of the fiber cable into the adapter LC connector.
- Insert the male fiber LC connector of the other end of the cable into the network switch.
