HD80958: Drafting (GenDraft) / Dimension value between same entities of t wo different section views are different

 

APAR status

  • Closed as program error.

Error description

  • Drafting (GenDraft) / Dimension value between
    same entities of two different section views are
    different
    .
    SCENARIO:
    .
    1. Start CATIA V5.
    2. Open Drawing1.CATDrawing.
    3. On B-B Section, create Intersection point
    between line and circle.
    4. On B-B Section, Create dimension by Centre line
    and Intersection point.
    >> 0.75 dimension is created.
    5. On A-A Section, create Intersection point
    between same entities.
    6. On A-A Section, Create dimension by Centre line
    and Intersection point.
    .
    RESULTS OBTAINED:
    .
    0.78 length dimension is created instead of 0.75.
    .
    EXPECTED RESULT:
    .
    As intersection point has been created between two
    same entities the dimension should be same.
    .

Local fix

Problem summary

  • Drafting (GenDraft) / Dimension value between
    same entities of two different section views are
    different
    .
    SCENARIO:
    .
    1. Start CATIA V5.
    2. Open Drawing1.CATDrawing.
    3. On B-B Section, create Intersection point
    between line and circle.
    4. On B-B Section, Create dimension by Centre line
    and Intersection point.
    >> 0.75 dimension is created.
    5. On A-A Section, create Intersection point
    between same entities.
    6. On A-A Section, Create dimension by Centre line
    and Intersection point.
    .
    RESULTS OBTAINED:
    .
    0.78 length dimension is created instead of 0.75.
    .
    EXPECTED RESULT:
    .
    As intersection point has been created between two
    same entities the dimension should be same.
    .

Problem conclusion

  • THIS PROBLEM WILL BE FIXED ON Virtual Design VERSION V5R21
    GA level.
    NOTE THAT THIS PROBLEM WILL ALSO BE FIXED ON V5R20 SP3.
    Additional Closure Information:
    Incident Diagnosis:
    Dimension value between same entities of two different
    section views are different
    .
    DEVELOPMENT REQUEST JUSTIFICATION:
    .
    An intersection point consists in a 2D point which is
    involved in 2 coincidence constraints. Being
    both coincident with 2 geometries, it is by definition,
    located at the intersection of the 2 elements.
    In the provided scenario, the intersection point was
    erroneously created as only one coincidence constraint was
    created. The coincidence with the cone intersection was not
    created, leading to a
    point arbitrary positioned. As a consequence, the dimension
    value was not relevant.
    .

Temporary fix

Comments

APAR Information

  • APAR number

    HD80958

  • Reported component name

    CATIA V5 NT>XP

  • Reported component ID

    569151000

  • Reported release

    518

  • Status

    CLOSED PER

  • PE

    NoPE

  • HIPER

    NoHIPER

  • Special Attention

    NoSpecatt

  • Submitted date

    2008-12-23

  • Closed date

    2010-05-14

  • Last modified date

    2010-05-14

  • APAR is sysrouted FROM one or more of the following:

  • APAR is sysrouted TO one or more of the following:

Fix information

  • Fixed component name

    CATIA V5 NT>XP

  • Fixed component ID

    569151000

Applicable component levels

  • R518 PSN

       UP

Rate this page:

(0 users)Average rating

Add comments

Document information


More support for:

CATIA V5

Software version:

518

Reference #:

HD80958

Modified date:

2010-05-14

Translate my page

Machine Translation

Content navigation