IBM 
p5 model 570 delivers
fast 2-way to 16-way POWER5 processing to mid-range rack-mounted servers
IBM United States
Hardware Announcement 104-257
July 13, 2004
 ENUS104-257.PDF (216KB)
|
At a glance
 |
| At a glance |
 |
The Model 570 offers:
- Modular rack-mount design with one to four 4U drawers in a single rack
- 1.5 GHz processors in 2-, 4-, 8-way configurations
- 1.65 GHz or 1.9 GHz processors in 2-, 4-, 8-, 12-, and 16-way configurations
- Up to 512 GB of DDR1 memory or 64 GB of DDR2 memory
- Up to 3,523.2 GB of internal disk storage
- Up to 24 hot-swap disk bays and 24 hot-swap PCI-X slots
- Up to eight slimline media bays for DVD-ROM and DVD-RAM
- Cluster 1600 enhancements — pSeries CSM support for model 570
- Dynamic LPAR and CoD
For ordering, contact:
Your IBM representative, an IBM Business Partner, or IBM Americas Call Centers at
800-IBM-CALL
(Reference: RE001).
Back to top
|
|
| Overview |
|
The IBM 
p5 model 570
Rack-mount Server (9117-570) gives you a modular mid-range solution for managing e-business
computing requirements.
The p5-570 uses a 4U rack-mounted server drawer as its basic building block and can be configured with one to four drawers in a single rack.
With two processor card positions per drawer, the p5 model 570 is available in 2-, 4-, 8-, 12-, and 16-way configurations.
The symmetric multiprocessor (SMP) server uses 2-way processor cards with state-of-the-art, 64-bit, copper-based, POWER5™ microprocessors running at either 1.5 GHz, 1.65 GHz, or 1.9 GHz. Each processor card has 36 MB of Level 3 cache and 8 slots for memory DIMMs. The base 2 GB of system memory can be expanded up to 512 GB in a four-drawer system.
Each drawer of a p5-570 system contains six disk drive bays and six 3.3-volt PCI-X slots. With up to 24 disk bays, the model 570 can accommodate up to 3,523.2 GB of internal disk storage. Each drawer can also hold two DVD-RAM or DVD-ROM drives.
Other integrated features include:
- Service processor
- Two 10/100/1000 Mbps Ethernet ports per drawer
- Two internal Ultra320 SCSI controllers per drawer
- Two serial ports per system
- Two USB 2.0 ports per drawer
- Two HMC ports per system
- Two remote I/O (RIO-2) ports per drawer
- Redundant hot-swap power and cooling
Dynamic logical partitioning (LPAR), with optional micropartitioning, and Capacity on Demand (CoD) are supported on the p5 model 570.
The p5-570 is supported with the IBM eServer® pSeries® Cluster 1600 running Cluster Systems
Management (CSM) V1.4 (AIX® and LINUX). For hardware control using CSM, an HMC is required.
Back to top
|
|
| Key prerequisites |
|
- Must be installed in your new or existing 7014 Model T00 or T42, or equivalent, rack
-
One of the following operating systems:
- AIX 5L for POWER™ V5.2 with the 5200-04 Recommended Maintenance Package (APAR IY56722), or later
- AIX 5L for POWER V5.3
- SUSE LINUX Enterprise Server 9 for POWER systems, or later
- Red Hat Enterprise Linux™ AS for POWER Version 3
Back to top
|
|
| Planned availability date |
|
August 31, 2004
Back to top
|
|
| Description |
|
Summary of standard features for p5 model 570:
- Configurations consist of 1, 2, 3, or 4 rack drawers, each 4U high.
- Systems can be 2-, 4-, 8-, 12-, or 16-way SMP design.
- 1.5 GHz, 1.65 GHz, or 1.9 GHz POWER5 64-bit processors cards, each 2-way.
- All processor cards are 2-way, with 0-way active. At least two processors must be activated by ordering the appropriate activation features.
- Two processor card slots per system drawer.
- Minimum of 2 GB of DDR1 266 MHz ECC memory — Expandable to 512 GB.
- Optional DDR2 533 MHz ECC memory supported only with 1.9 GHz processor card (#7833) — Expandable to 64 GB.
-
Six hot-swap disk drive bays per drawer — split 6-pack backplane.
- One to twenty-four internal SCSI disks
- Optional two media bays per drawer — Up to eight DVD-ROM or DVD-RAM features per system (optional).
- Two RIO-2 ports per drawer for attaching external 7311 I/O drawers.
-
A maximum of six hot-swap PCI-X slots per drawer:
- Five 64-bit, 3.3 volt, 133 MHz (long).
- One 64-bit, 3.3 volt, 133 MHz (short); this slot can also be used to support the RIO-2 Remote I/O Loop Adapter (#1800), if needed.
- Two hot-swap power supplies per drawer.
- One service processor.
-
Integrated functions in each drawer:
- Dual 10/100/1000 Mbps Ethernet ports
- Two Ultra320 SCSI controllers (internal) with support for an optional RAID daughter card
- Redundant hot-swap cooling fans
- Two USB 2.0 ports
- Two serial ports per system
- Two HMC ports per system
- Two Remote I/O (RIO-2) ports
Capacity on Demand
The Capacity on Demand (CoD) suite of offerings provides permanent nondisruptive growth as well as temporary additional capacity for short term processing needs.
Available for a fee, CoD allows additional processors and memory to be brought on line as they are needed to meet increasing workload demands. If the system is configured for dynamic LPAR, this can be accomplished without impacting operations and avoiding costly downtime.
These features have significant value for users who want to upgrade without disruption, enhance their system RAS (reliability, availability, serviceability) characteristics, or simply grow with a finer level of granularity. The CoD features allow a system to be manufactured (or upgraded) with inactive processors and memory.
The hardware is delivered with these features built in, ready to be activated when needed. It can turned on by ordering processor or memory activation features. An activation code entered at the HMC enables the resource either permanently or temporarily, depending on which activation feature is ordered.
Types of CoD Activations
Permanent CUoD for Processors and Permanent CUoD for Memory are activations that permanently enable inactive processors or memory for future use.
On/Off CoD enables users to temporarily activate processors and memory. Processors and memory may be activated and turned off an unlimited number of times whenever the client desires additional processing resources. This offering provides a system administrator an interface at the HMC to manage the activation and deactivation of resources. A monitor resides on the server and logs the usage activity. Clients must send this usage data to IBM monthly. A bill is then generated based on the total amount of processor and memory resources utilized, in increments of processor and memory (1 GB) days.
Reserve CoD represents an "autonomic" way to activate temporary capacity. Reserve CoD enables the user to place a quantity of inactive processors into the server's Shared Processor Pool, which then become available to the pool's resource manager. When the server recognizes the number of base (purchased/active) processors assigned across uncapped partitions have been 100% utilized, and at least 10% of an additional processor is needed, then a processor day (good for a 24-hour period) is charged against the Reserve CoD account balance. Another processor day will be charged for each additional processor put into use based on the 10% utilization rule. After a 24-hour period elapses, and there is no longer a need for the additional performance, no processor days will be charged until the next performance spike.
Trial Capacity on Demand (Trial CoD) is a function delivered with all pSeries servers having inactive CoD processors or memory.
Servers with inactive CoD processors or memory will be capable of using a one-time, no-cost activation for a maximum period of 30 consecutive days. This enhancement allows for benchmarking of CoD resources or can be used to provide immediate access to inactive resources while the purchase of permanent or temporary activations is pending.
Accessibility by people with disabilities
IBM eServer p5 570 is capable as of August 31, 2004, when used in accordance with IBM's
associated documentation, of satisfying the applicable requirements of Section 508 of the
Rehabilitation Act, provided that any assistive technology used with the product properly
interoperates with it.
Back to top
|
|
| Statement of general direction |
|
IBM plans to extend the capabilities of the IBM eServer p5 product line by introducing support for the i5/OS operating system. This support is planned for selected eServer p5 570 and future high-end eServer p5 models. i5/OS support will provide additional flexibility for large-scale server consolidation where AIX 5L and/or Linux is the primary operating system. i5/OS support will be limited to one processor on selected p5 570 models and up to two on selected high-end models. This capability is planned to be available in the first half 2005.
All statements regarding IBM's future direction and intent are subject to change or withdrawal
without notice, and represent goals and objectives only. References to list prices refer to IBM
list prices only. Reseller prices may vary.
Back to top
|
|
| Reference information |
|
Refer to Software Announcement 204-155 , dated July 13, 2004, for AIX 5L for POWER V5.3.
Trademarks
Back to top
|
|
| IBM Tivoli® Security |
|
Overview
Tivoli security-ready clients and agents are planned to be pre-installed on POWER5™ servers running AIX® 5L
V5.2 beginning in August 2004. Pre-installed Tivoli security-ready clients and agents for
POWER4+™ and POWER4™ pSeries® servers running AIX 5L V5.2 also are planned to be available
beginning in August 2004. IBM intends to pre-install security-ready clients and agents on
eServer® and pSeries POWER™ servers that support AIX 5L V5.3 in the future.
The pre-installed security clients and agents software, when coupled with optional and extra cost server-based IBM Tivoli security management solution offerings, give eServer and pSeries customers security capabilities to help address a fundamental and heightened customer need for more secure on demand systems.
Tivoli security (identity) management solutions offer critical layers of additional defense beyond the traditional perimeter defense provided by firewalls: antivirus software, intrusion detection software, a security control layer, and a security policy compliance layer.
The Tivoli control layer determines which server users can access and what users may view and do. The Tivoli security compliance layer helps to ensure that customers are in, and remain in, compliance with security policies while helping assess security risks and initiating responses to security events.
Highlights IBM Tivoli security-ready clients/agents: Now every eServer pSeries POWER5, POWER4+, and POWER4 server with AIX 5L V5.2 is available with pre-installed Tivoli security-ready client and agent software.
- Client for IBM Tivoli Access Manager for Operating System AIX
- Agent for IBM Tivoli Identity Manager
- Agent for IBM Tivoli Risk Manager
- Client for IBM Tivoli Security Compliance Manager
To use each Tivoli security-ready client or agent, acquisition of the following corresponding server-based Tivoli security management product offering is required.
- IBM Tivoli Access Manager for Operating System AIX
- IBM Tivoli Identity Manager
- IBM Tivoli Risk Manager
- IBM Tivoli Security Compliance Manager
When pre-installed, the security-ready clients/agents help to simplify the implementation and enablement of Tivoli security management solutions. The solutions enable a consistent enforcement of security management policies across eServer, pSeries, and AIX 5L as well as across heterogeneous server environments running UNIX®, Linux™, and Microsoft™ Windows™ operating systems.
Optional IBM Tivoli Security Management Offerings for pSeries AIX 5L: Tivoli security-ready clients and agents for eServer and pSeries AIX 5L servers provide the means for Tivoli security management software running on an eServer or a pSeries AIX 5L server to provide and manage two different layers of security (a control layer or a security policy compliance layer) for each connected and enabled server client. One Tivoli security management server can manage up to thousands of eServer or pSeries AIX 5L server clients. Security management capabilities include:
- Secure and manage the pSeries AIX 5L Server: IBM Tivoli Access Manager for Operating System AIX is optional, server-based enablement software that provides multiple eServer or pSeries AIX 5L server clients with IBM mainframe-class security. Access Manager can lock down and harden the AIX 5L operating system at the root level to help secure applications and protect data, meet customer security audit requirements, and reduce security administration costs.
- Setup and manage the users: IBM Tivoli Identity Manager is optional, server-based enablement software that automates the creation and management of multiple user accounts. Identity Manager helps to significantly shorten the time for provisioning users from weeks to minutes and automatically discovers invalid user accounts.
- Manage security operations: IBM Tivoli Risk Manager is optional, server-based enablement software that centrally monitors, reports and manages security events. Risk Manager helps to radically improve the administration of the whole security management environment.
- Audit security policies for compliance: IBM Tivoli Security Compliance Manager is optional, server-based enablement software that checks the server system, middleware, and applications for vulnerability and adherence to customer security policies. Security Compliance Manager determines violations against security policies provided by IBM or modified or written by the customer.
Complementary (Security) Offering IBM Tivoli Directory Server
- Store Users and Their Identities: IBM Tivoli Directory Server is server-based enablement software. Directory Server is foundation service software for building security-rich and standards-compliant identity infrastructure solutions. It provides a robust and lightweight directory access protocol (LDAP) and offers a choice of simple user ID and password authentication or robust digital certificate-based authentication. Directory Server is provided as a part of the AIX 5L V5.2 Expansion Pack.
Customer value: Tivoli security management solutions for pSeries AIX 5L can significantly help meet the heightened and growing customer need for a more secure on demand IT and server operating environment.
Tivoli security-ready client and agent software provides customer value when pre-installed. Pre-installation with AIX 5L helps save installation planning and implementation time when the clients/agents are security enabled by Tivoli security management (server) offerings.
Significant additional customer value is delivered when the Tivoli security-ready clients/agents are connected to and enabled by Tivoli security management (server) software:
- Helps protect and optimize IT resources by controlling who has access to what
- Helps reduce the cost of security administration and support
- Helps manage complexity with a single user sign-on and unified user experience
- Helps validate compliance against security policies and audits requirements
IBM Tivoli Security Management Solutions Information Sources
Worldwide
- Tivoli sales support (ibm.com Web site)
- Tivoli technical support
-
Tivoli security sales:
- IBM Direct: Bob Kalka, bkalka@us.ibm.com
- IBM Business Partners: Rob Ciampa, rciampa@us.ibm.com
Americas
- Tivoli sales and technical support: 800-426-7378
- Tivoli security sales: Craig J. Lund, clund@us.ibm.com
- Tivoli technical support
Note:
All statements regarding IBM's future direction and intent are subject
to change or withdrawal without notice and represent goals and objectives
only.
Back to top
|
|
| Publications |
|
The following information is shipped with the 9117-570. Additional copies are available. To order, contact your IBM representative.
Order
Title number
IBM eServer Hardware Information SK3T-8159
Center CD-ROM
IBM eServer Safety Information G229-9054
Setup Instructions SA41-5156
IBM Statement of Limited Warranty Z125-4753
IBM License Agreement for Z125-5468
Machine Code
Pointer Sheet for Machine Internal GC52-1065
Code License Agreement
Back to top
|
|
| Services |
|
Integrated Technology Services
IBM services include business consulting, outsourcing, hosting services, applications, and other technology management.
These services help you learn about, plan, install, manage, or optimize your IT infrastructure for e-business. They can help you integrate your high-speed networks, storage systems, application servers, wireless protocols, and an array of platforms, middleware, and communications software for IBM and many non-IBM offerings. IBM is your one-stop shop for IT support needs.
For details on available services, contact your IBM representative or visit
For details on education offerings related to specific products, visit
Select your country, and then select the product as the category.
Back to top
|
|
| Technical information |
|
p5 Model 570 System Unit
- Width: 483 mm (19.0 in)
- Depth: 790 mm (31.1 in)
- Height: 174.1 mm (6.85 in)
- Weight: 63.6 kg (140 lb)
Dimensions and specifications shown are for a single drawer. Model 570 systems can have one to four drawers.
To help assure installability and serviceability in non-IBM, industry-standard racks, review the vendor's installation planning information for any product-specific installation requirements.
Operating environment
- Temperature: 5° to 35°C (41° to 95°F)
- Relative humidity: 8% to 80%
- Maximum wet bulb: 23°C (73°F) (operating)
- Noise level: 6.5 bels (operating)
Power requirements
- Operating voltage: 200 to 240 V ac 50/60 Hz
- Power consumption: 1,300 watts (maximum per 4-way drawer)
- Power source loading: 1.37 kVA (per drawer maximum configuration)
- Thermal output: 1,349 joules/sec (4,437 Btu/hr) (per drawer maximum configuration)
EMC conformance classification
This equipment is subject to FCC rules and it shall comply with the appropriate FCC rules before final delivery to the buyer or centers of distribution.
- U.S. — FCC CFR47 Part 15 Class A
- Europe — CISPR 22 Class A; "CE" Mark of Conformity
- Japan — VCCI-1
- Korea — Korean Requirement Class A
Homologation — Telecom environmental testing (Safety and EMC): Homologation approval for specific countries has been initiated with the IBM Homologation and Type Approval (H&TA) organization in LaGaude.
This IBM pSeries model and applicable features meet the environmental testing requirements of the country Telecom and have been designed and tested in compliance with the Full Quality Assurance Approval (FQAA) process as delivered by the British Approval Board for Telecom (BABT), the U.K. Telecom Regulatory authority.
Product safety/Country testing/Certification
- U.S.: UL
- Canada: CNL (CSA or cUL)
- Germany/Europe: GS Mark (Safety, TUV, EN60 950)
General requirements
The p5 model 570 is in compliance with IBM Corporate Bulletin C-B 0-2594-000 Statement of Conformity of IBM Product to External Standard (Suppliers Declaration).
Hardware requirements
The p5 model 570 must be installed in a new or existing 7014-T00 or T42 rack with power distribution features 9176, 9177, 9178, or 9188, or equivalent rack. This provides:
- Proper dimensions
- Mounting surfaces
- Power distribution
- Ventilation
- Stability
- Other functional requirements
The design of the p5 model 570 is optimized for use in an IBM 7014-T00 or T42 rack. Both the front cover and the processor flex cables occupy space on the front left side of an IBM 7014 rack that may not be available in typical non-IBM racks.
The SMP cables are designed specifically to support seamless (4-way node) upgradability and future concurrent maintenance features of these POWER5 systems. The use of non-IBM racks may limit your ability to exploit these ease-of-use, upgradability, and serviceability enhancements in the future.
Minimum system configuration — IBM eServer p5 model 570: The IBM eServer p5 model 570 is based on a flexible, modular design that can be configured with up to
- Four drawers
- 16 processors
- 512 GB of system memory
- 24 disk drives
- 24 PCI slots
- Eight media devices
This flexibility is delivered through the many optional features available for the model 570. Each new model 570 system must include a minimum of the following items:
-
One system drawer (4U) with the following:
- One system drawer enclosure (#7879)
- One language group specify (#9XXX)
- Two power cords (#64XX)
- One Rack-mount Rail Kit (#7164 or #7165)
-
One processor card — choose from any available processor features:
- 2-Way 1.65 GHz, 0-Way Active, DDR1 (#7830 — default minimum)
-
Two processor activations — depending on the processor features ordered:
- Processor activation for #7830 (2x #7897 — default minimum)
-
2 GB memory minimum — choose from any available memory features:
- 2048 MB memory (4 x 512 MB DIMMs) (#4452 — default minimum)
-
One disk drive, 36 GB or larger — choose from any available disk features:
- 36.4 GB 10K rpm Ultra320 SCSI Disk (#3273 — default minimum)
-
Additional required features:
-
One SCSI disk backplane (#7868)
- Two power supplies (#7888)
- One system midplane (#7867)
- One operator panel (#1846)
- One I/O backplane, 6 PCI-X slots (#7866)
- One processor enclosure and backplane (#7865)
- One power distribution backplane (#7870)
- One processor power regulator (#7875)
-
One SCSI disk backplane (#7868)
Additional optional features can be added, as desired.
Value Paks: Value Paks are available only for initial system orders. They provide a convenient way to order any of several configurations designed to meet typical customer requirements. Special reduced pricing is available when a system order satisfies specific configuration requirements for memory, disk drives, and processors. When a Value Pak is ordered, the configurator offers a choice of starting points that can be added onto.
Customers can configure systems with 2 to 16 processors and 2 to 16 processor activations. With the purchase of a Value Pak, for each paid processor activation, the customer is entitled to one processor activation at no additional charge, if the following requirements are met:
- The system must have at least two disk drives of at least 73.4 GB each.
- There must be at least 2 GB of memory installed for each activated processor.
p5 570 Express Value Paks for 1.5 GHz Processors and DDR1 Memory
Configurator starting points:
- 2-way (1 x 7834), 4 GB (2 x 4452), 2 x 73 GB (2 x 3274), 1 x 7929 + 1 x 8456 entitlements
- 4-way (2 x 7834), 8 GB (4 x 4452), 2 x 73 GB (2 x 3274), 2 x 7929 + 2 x 8456 entitlements
- 8-way (4 x 7834), 16 GB (8 x 4452), 2 x 73 GB (2 x 3274), 4 x 7929 + 4 x 8456 entitlements
Value Paks for 1.65 GHz Processors and DDR1 Memory
Configurator starting points:
- 2-way (1 x 7830), 4 GB (2 x 4452), 2 x 73 GB (2 x 3274), 1 x 7897 + 1 x 8452 activations
- 4-way (2 x 7830), 8 GB (4 x 4452), 2 x 73 GB (2 x 3274), 2 x 7897 + 2 x 8452 activations
- 8-way (4 x 7830), 16 GB (8 x 4452), 2 x 73 GB (2 x 3274), 4 x 7897 + 4 x 8452 activations
Value Paks for 1.9 GHz Processors and DDR1 Memory
Configurator starting points:
- 4-way (2 x 7832), 8 GB (4 x 4452), 2 x 73 GB (2 x 3274), 2 x 7898 + 2 x 8454 activations
- 8-way (4 x 7832), 16 GB (8 x 4452), 2 x 73 GB (2 x 3274), 4 x 7898 + 4 x 8454 activations
- 16-way (8 x 7832), 32 GB (16 x 4452), 2 x 73 GB (2 x 3274), 8 x 7898 + 8 x 8454 activations
Value Paks for 1.9 GHz Processors and DDR2 Memory
Configurator starting points:
- 4-way (2 x 7833), 8 GB (4 x 7892), 2 x 73 GB (2 x 3274), 2 x 7899 + 2 x 8455 activations
- 8-way (4 x 7833), 16 GB (8 x 7892), 2 x 73 GB (2 x 3274), 4 x 7899 + 4 x 8455 activations
- 16-way (8 x 7833), 32 GB (16 x 7892), 2 x 73 GB (2 x 3274), 8 x 7899 + 8 x 8455 activations
Software requirements
If installing AIX on the system (one of these):
-
AIX Version 5L for POWER V5.2 with the 5200-04 Recommended Maintenance Package (APAR IY56722),
or later
Note: Advanced POWER Virtualization feature (#7942) is not supported on AIX 5L for POWER V5.2.
- AIX 5L for POWER V5.3, or later
If installing Linux on the system (one of these):
- SUSE LINUX Enterprise Server 9 for POWER, or later
-
Red Hat Enterprise Linux AS for POWER Version 3 (planned availability date:
September 30, 2004)
Note: Not all p5-570 system features available under the AIX operating system are available under the Linux operating system.
Information on features and external devices supported by Linux on the model 570 can be found at
If installing the model 570 server within the Cluster 1600:
- CSM V1.4 (AIX or Linux)
Limitations
Processors
- A p5 570 system can have from 1 to 4 system drawers. Each drawer has two processor slots. A system with one drawer may have one or two processor cards installed. A system with 2, 3, or 4 drawers must have two processor cards in each drawer.
- When two or more processor cards are installed, all cards must have the same processor frequency.
- Each processor card has two processors and eight memory DIMM slots. The DIMM slots are different for DDR1 and DDR2 memory. All processor cards must support the same memory technology, either DDR1 or DDR2.
- Systems configured with 1.5 GHz processors have a maximum of eight processors and two drawers.
Memory
- The 9117-570 must contain a minimum of 2 GB of system memory. Memory is expandable up to a maximum of 512 GB with DDR1 DIMMs, or a maximum of 256 GB with DDR2 DIMMs.
- Memory is installed in groups of four DIMMs mounted on the processor cards. Each processor card has 8 DIMM slots.
- DDR1 memory is supported on 1.5 GHz processor cards (#7834), 1.65 GHz processor cards (#7830), and 1.9 GHz processor cards (#7832). DDR2 memory is supported only on 1.9 GHz processor cards (#7833). All DIMMs in a 570 system must use the same memory technology, either DDR1 or DDR2.
- Each processor card must have at least 2 GB of memory installed.
- It is recommended that each processor card have an equal amount of memory installed. Balancing memory across the installed processor cards allows memory accesses in a coordinated parallel manner and can be utilized to provide optimal performance.
- 8 GB DIMMS cannot be installed on the same processor card with smaller capacity DIMMS. This rule applies to the #4492 and #7935 memory features.
- Plans for future memory upgrades should be taken into account to obtain optimal performance without limiting future memory expansion.
Power
- Two power supplies must be ordered to provide redundancy for enhanced system availability.
Racks
- The model 570 consists of 1 to 4 system drawers. Each drawer occupies 4U of vertical rack space. The p5-570 is designed to be installed in a 7014-T00 or 7014-T42 rack. An existing T00 or T42 rack can be used for model 570 if sufficient space and power are available. Model 570 is not supported in the withdrawn 7015-R00 and 7014-S00 racks.
- For p5-570 configurations with 2, 3, or 4 drawers, all drawers must be installed together in the same rack, in a continuous space of 8U, 12U, or 16U within the rack.
- When a p5 570 system is installed in an IBM 7014-T00 or 7014-T42 rack that has no front door, a Thin Profile Front Trim Kit must ordered for the rack. The front bezel on a model 570 drawer is too wide to be used with the previously announced rack trim kits (features #6107 and #6081). The required trim kit for the 7014-T00 rack is feature #6246. The required trim kit for the 7014-T42 rack is feature #6247.
- The IBM 7014-T42 rack is constructed with a small flange at the bottom of EIA™ location 37. This requires special placement rules when a model 570 system is installed near the top of a 7014-T42 rack, to avoid interference with the front bezel or with the front flex cable, depending on the system configuration. No system drawer can be installed in EIA positions 34, 35, or 36. A two-drawer system cannot be installed above position 33. A three-drawer system cannot be installed above position 25. A four-drawer system cannot be installed above position 21. The position number refers to bottom of the lowest drawer.
-
The design of the p5 model 570 is optimized for use in an IBM 7014-T00 or
T42 rack. Both the front cover and the processor flex cables occupy
space on the front left side of an IBM 7014 rack that may not be
available in typical non-IBM racks.
The SMP cables are designed specifically to support seamless (4-way node) upgradability and future concurrent maintenance features of these POWER5 systems. The use of non-IBM racks may limit your ability to exploit these ease-of-use, upgradability, and serviceability enhancements in the future.
I/O drawers
- Model 570 systems can be attached to 7311-D10, 7311-D11, or 7311-D20 I/O drawers, using the standard and optional RIO-2 ports.
-
The maximum number of attached RIO-2 I/O drawers depends on the number of
system drawers, as follows:
- One-drawer systems support up to 8 I/O drawers
- Two-drawer systems support up to 12 I/O drawers
- Three-drawer systems support up to 16 I/O drawers
- Four-drawer systems support up to 20 I/O drawers
- When a 7311-D10 or 7311-D20 I/O drawer is attached to a model 570 system, the I/O drawer must be configured with a RIO-2 Remote I/O adapter. The supported RIO-2 adapter for 7311-D10 is feature #6431. The supported RIO-2 adapter for 7311-D20 is feature #6417. The previous RIO adapters, #6414 and #6413, cannot be used for attachment to a model 570 system.
-
When a 7311-D10 or a 7311-D20 I/O drawer is attached to a model 570
system, some PCI adapters are not supported. The following 7311-D10
and/or 7311-D20 features must not be installed in an I/O drawer if it is
attached to a model 570 system. If they are present in a previously
configured I/O drawer, they must be removed prior to attachment to a p5
570.
- IBM Short-wave Serial HIPPI PCI Adapter for RS/6000® (#2732)
- IBM Long-wave Serial HIPPI PCI Adapter for RS/6000 (#2733)
- S/390® ESCON® Channel PCI Adapter (#2751)
- IBM ARTIC960RxD Quad Digital Trunk PCI Adapter (#6310)
- SP™ Switch2 PCI-X Attachment Adapter (#8398)
I/O drawer attachment
- It is recommended that any attached I/O drawers be located in the same rack as the p5-570 server for ease of service, but they can be installed in separate racks, if desired.
-
I/O drawers are connected to the p5-570 drawer via the following cables:
- RIO cables for data transfer
- Power control cables
- RIO cable connections are always made in loops to help protect against a single point-of-failure resulting from an open, missing, or disconnected cable. Model 570 systems with non-looped configurations could experience degraded performance and serviceability. If a non-loop connection is detected, a problem is reported.
- Each p5-570 system drawer has two integrated RIO-2 ports, which support a single RIO loop. If a second RIO loop is required, two additional RIO-2 ports can be configured by ordering the #1800 RIO-2 adapter.
- When the #1800 RIO-2 adapter is installed in a system drawer, no adapter cards can be installed in PCI-X slot #6. The #1800 RIO-2 adapter is supported only in system drawers that have two processor cards.
-
Up to eight RIO loops are available, each supporting up to four I/O
drawers and up to a maximum of twenty I/O drawers per system. A minimum
of two RIO cables are required to attach the first I/O drawer on each RIO
loop. A third drawer-to-drawer RIO cable is required to complete the
loop when an additional I/O drawer is attached to the loop. RIO cables
are available in various lengths to attach I/O drawers within a single
rack or across multiple racks, if desired.
- #3146 = 1.2 meters
- #3147 = 3.5 meters
- #3148 = 10 meters
- #3156 = 1.75 meters
- #3168 = 2.5 meters
- Power control for the I/O drawers is provided via one loop per drawer. The number of power control (SPCN) cables required is equal to one plus the number of I/O drawers attached to the system drawer. A minimum of two power control cables (#6006 = 3 meters, #6029 = 30 meters) are required for attachment of the first I/O drawer. Each additional I/O drawer requires one additional power control cable to complete the loop attachment.
Integrated I/O ports
- Each system has only two HMC ports, regardless of the number of system drawers. For systems configured with more than one system drawer, the HMC ports are in the same drawer as the Service Processor (#7881).
- Although each system drawer is equipped with two integrated serial port external connectors, only two serial ports are activated in a multidrawer configuration. Integrated serial ports are activated in the drawer that has the Service Processor (#7881) installed. Integrated serial ports in other system drawers are not functional.
- Integrated serial ports are not supported when the HMC ports are connected to a Hardware Management Console. Either the HMC ports or the integrated serial ports can be used, but not both.
- The integrated serial ports are supported only for modem and async terminal connections. Any other applications using serial ports require a separate serial port adapter to be installed in a PCI slot. The integrated serial ports do not support HACMP™ configurations.
Disks, media, and boot devices
- Boot is supported via SCSI adapters, or from a network via LAN adapters.
- The minimum configuration requires at least one disk drive having a capacity of 36.4 GB or greater.
- Each system drawer can support up to two media devices when the optional #7869 media backplane is ordered. Any combination of DVD-ROM and DVD-RAM drives can be installed, up to eight media devices in a four-drawer system.
PCI slots and adapters
- Each p5-570 system drawer has six PCI-X slots. All slots operate at 3.3 volts. There are five full-length 64-bit slots and one short 64-bit slot.
- The p5-570 PCI slot population rules are complex. The following PCI slot and adapter limitations are provided for general guidance. Extensive configuration rules and checking procedures are incorporated into the ECFGRS6000 configurator to help ensure valid system configurations. Configurations generated without utilizing the ECFGPWR configurator may create orders that cannot be manufactured, resulting in possible order rejection and delayed delivery.
- System maximum limits for adapters and devices may not provide optimal system performance. These limits are given to assist with connectivity and functional assurance.
- When the model 570 is attached to one or more I/O drawers, additional rules apply for some PCI adapters regarding the maximum supported adapter quantities for the combined system. For adapters not shown in the list below, the combined maximum quantity is determined by the maximum quantities for each attached I/O drawer. The adapters in the following list are limited to the combined maximum quantity shown.
8-Port Asynchronous Adapter EIA-232/RS-422, PCI bus (2943) 42 128-Port Asynchronous Controller, PCI bus (2944) 42 PCI Universal Differential Ultra SCSI Adapter (6204) 42 POWER GXT135P Graphics Accelerator w/Digital Support (2849) 8 IBM Token-Ring PCI Adapter (4959) 20 IBM e-business Cryptographic Accelerator (4960) 32
Hot-plug options
-
The following options are hot-plug capable:
- System power supplies
- Disk drives
- Most PCI adapters
- Service processors
- Processor power regulators
- Hot-plug procedures are contained in the eServer p5 model 570 Installation Guide .
- Any PCI adapter supporting the system boot device or system console is not hot-plugged.
-
The following adapters are not hot-plug capable:
- POWER GXT135P Graphics Accelerator with Digital Support (#2849)
- 2-Port Multiprotocol PCI Adapter (#2962)
Logical Partitioning (LPAR)
- Dynamic LPAR allows up to one partition per processor.
- Up to ten partitions per processor are supported when Advanced POWER Virtualization (#7942) is ordered. This function requires AIX 5L V5.3 or SUSE SLES 9 for POWER.
- A Hardware Management Console is required for all LPAR configurations.
- For Linux partitions, a DVD-ROM or DVD-RAM and a Media Enclosure and Backplane (#7869) are required.
Model conversion
- Customers who own an IBM pSeries 650 (7038-6M2) may convert their system to an IBM eServer p5 570 system. System hardware for the new model will consist of one or more drawers to replace the old system chassis. Supported features from the old model will be transferred to the new system. The same configuration rules apply to model conversions and to new system orders.
- Model conversions allow any valid number of processors in the new model, regardless of the number of processors in the old model. The valid processor quantities are 2, 4, 8, 12, and 16.
- Any supported memory and disk drive features that are transferred from the old system can be counted toward the requirements for processor activations at no additional charge, using the same Value Pak rules that apply to new system orders.
Planning information
Cable orders: No additional cables are required.
Security, auditability, and control
This product uses the security and auditability features of the operating system and application software.
The customer is responsible for evaluation, selection, and implementation of security features, administrative procedures, and appropriate controls in application systems and communications facilities.
Integrated Technology Services (IBM Global Services)
Integrated Technology Services offers customers a comprehensive list of on-site services to implement, manage, and tune eServer p5 570. Each service is tailored to the specific configuration and customer requirements. Available services include:
- Implementation Services for IBM eServer p5 and pSeries LPAR: Planning and implementation of p5 570 including on-site installation of hardware, system software, and configuration of LPAR environment
- IBM Migration Services for eServer p5 and pSeries: Planning, assistance and training for migrating to a POWER5 environment
- IBM Implementation Services for eServer Cluster 1600: Installation, configuration, customization, testing, and verification of a clustered environment
- High Availability Cluster Implementation for eServer: Design, development, and implementation of high-availability cluster environment for critical business needs
- IBM Technology Assessment and Consulting Services: Consulting services that analyze IT resources, identify cost saving opportunities through consolidation and recommend environmental changes to reduce the total cost of computing
Contact your IBM representative for the list of selected services available in your country, either
as standard or customized offerings for the efficient installation, implementation, and/or
integration of this product.
Back to top
|
|
| IBM Electronic Services |
|
IBM Global Services has transformed its delivery of hardware and software support services to put you on the road to higher systems availability. IBM Electronic Services is a Web-enabled solution that provides you with an exclusive, no-additional-charge enhancement to the service and support on the IBM eServer. You should benefit from greater system availability due to faster problem resolution and preemptive monitoring. IBM Electronic Services is comprised of two separate but complementary elements: IBM Electronic Services news page and IBM Electronic Service Agent™.
IBM Electronic Services news page provides you with a single Internet entry point that replaces the multiple entry points traditionally used by customers to access IBM Internet services and support. By using the news page, it enables you to gain easier access to IBM resources for assistance in resolving technical problems.
The IBM Electronic Service Agent is no-additional-charge software that resides on your IBM eServer system that is designed to proactively monitor events and transmit system inventory information to IBM on a periodic customer-defined timetable. The IBM Electronic Service Agent tracks system inventory, hardware error logs, and performance information. If the server is under a current IBM maintenance service agreement or within the IBM warranty period, the Service Agent automatically reports hardware problems to IBM. Early knowledge about potential problems enables IBM to provide proactive service that maintains higher system availability and performance. In addition, information collected through the Service Agent will be made available to IBM service support representatives when they are helping answer your questions or diagnosing problems.
To learn how IBM Electronic Services can work for you, visit
Back to top
|
|
| Terms and conditions |
|
This product is available for purchase under the terms of the IBM Customer Agreement (ICA).
Each IBM machine is manufactured from parts that may be new or used. In some cases, a machine may not be new and may have been previously installed.
Regardless, IBM's appropriate warranty terms apply.
Volume orders: Contact your IBM representative.
IBM Global Financing: Yes
Warranty period: One year
Warranty service: If required, IBM provides repair or exchange service. An IBM technician will attempt to resolve your problem over the telephone. You must follow IBM's problem determination and resolution procedures. Scheduling of service will depend upon the time of your call and is subject to parts availability. Service levels are response time objectives and are not guaranteed. The specified level of warranty service may not be available in all worldwide locations. Additional charges may apply outside IBM's normal service area. Contact your local IBM representative or your reseller for country- and location-specific information.
Customer replaceable unit (CRU) service
IBM provides replacement CRUs to you for you to install. CRU information and replacement instructions are shipped with your machine and are available from IBM at any time on your request. CRUs are designated as being either a Tier 1 or a Tier 2 CRU. Installation of Tier 1 CRUs is your responsibility. If IBM installs a Tier 1 CRU, at your request, you will be charged for the installation. You may install a Tier 2 CRU yourself or request IBM to install it, at no additional charge under the type of warranty service specified below, On-site Service. IBM specifies in the materials shipped with a replacement CRU whether a defective CRU must be returned to IBM. When return is required, return instructions and a container are shipped with the replacement CRU, and you may be charged for the replacement CRU if IBM does not receive the defective CRU within 30 days of your receipt of the replacement.
The following are designated as Tier 1 CRU parts:
- AC power cord
- AC power supply
- Disk drive
- DVD drive
- Fan
- Flex cable
- I/O adapters
- Media enclosure and backplane
- Operator panel
- Processor power regulator
- Service processor
On-site service
IBM On-site repair limited, next-business-day, on-site response time, latest call registration 12:00 p.m., 5 days per week by 9 hours, (excluding public and national holidays).
IBM will repair the failing machine at your location and verify its operation. You must provide a suitable working area to allow disassembly and reassembly of the IBM machine. The area must be clean, well-lit, and suitable for the purpose.
Warranty service upgrade
- IOR, Monday through Friday, 8:00 a.m. to 5:00 p.m. local time, excluding IBM holidays, 4-hour average response1
- IOR, 24 hours per day, 7 days a week, 4-hour average response1
- IOR, 24 hours per day, 7 days a week, 2-hour average response1
- 1
- This type of repair service provides a response objective and is not a guarantee.
The designation of a part as IOR or CRU is independent of response time. It is possible that when upgrading to a warranty with improved response time, the appropriate problem resolution will still be to ship a CRU part to you for that installation. IBM will replace a CRU part at your request at no charge, if the system is covered by a same-day warranty service upgrade.
ServiceSuite™ and ServiceElect (formerly ESA) maintenance: For ServiceElect (Z125-5510) and ServiceSuite (Z125-5745) Statements of Work:
Maintenance services: If required, IBM provides repair or exchange service upgrades depending on the type of service specified for your machine. An IBM technician will attempt to resolve your problem over the telephone. You must follow IBM's problem determination and resolution procedures. Scheduling of service will depend upon the time of your call and is subject to parts availability. Service levels are response time objectives and are not guaranteed. The specified level of service may not be available in all worldwide locations. Additional charges may apply outside IBM's normal service area. Contact your local IBM representative or your reseller for country- and location-specific information.
- CRU service: If your problem can be resolved with a CRU (for example, keyboard, mouse, speaker, memory, HDD, and other easily replaceable parts), IBM will ship these parts to you for replacement by you. If IBM instructs you to return the replaced CRU, you are responsible for returning it to IBM in accordance with IBM's instructions. If you do not return the defective CRU, if IBM so instructs, within 30 days of your receipt of the replacement CRU, IBM may charge you for the replacement.
-
On-site service: IOR, 9 hours per day, Monday through Friday excluding
holidays, next-business-day response or 24 hours per day, 7 days a week,
same-day response.
IBM will repair the failing machine at your location and verify its operation. You must provide a suitable working area to allow disassembly and reassembly of the IBM machine. The area must be clean, well-lit, and suitable for the purpose.
- IOR, Monday through Friday, 8:00 a.m. to 5:00 p.m. local time, excluding IBM holidays, next-business-day service
- IOR, Monday through Friday, 8:00 a.m. to 5:00 p.m. local time, excluding IBM holidays, 4-hour average response1
- IOR, 24 hours per day, 7 days a week, 4-hour average response1
- IOR, 24 hours per day, 7 days a week, 2-hour average response1
IBM will replace a CRU part at your request, at no charge, if the system is covered by a same-day maintenance service.
Usage plan machine: No
IBM hourly service rate classification: Two
When a type of service involves the exchange of a machine part, the replacement may not be new, but will be in good working order.
Field-installable features: Yes
Model conversions: Yes
Machine installation: Installation is performed by IBM. IBM will install the machine in accordance with the IBM installation procedures for the machine. In the United States, contact IBM at 800-IBM-SERV (426-7378) and in other countries contact the local IBM office.
The Machine Installation Guide specifies site preparation, physical requirements and installation (operating) environment and any cabling included in the installation along with the approximate installation time in hours. Customer requests for installation of items not covered in the installation guide may be performed at IBM's hourly service rate designated for the machine.
Graduated charges: Yes
Group number: F5
Licensed machine code: IBM Machine Code is licensed for use by a customer on the IBM machine for which it was provided by IBM under the terms and conditions of the IBM License Agreement for Machine Code, to enable the machine to function in accordance with its specifications, and only for the capacity authorized by IBM and for which the customer has paid. Machine code may sometimes be referred to as "Licensed Internal Code" or "LIC" in documentation or on the machine with which the machine code was delivered. All such code, whether referred to or marked as machine code, Licensed Internal Code, or LIC is subject to the IBM License Agreement for machine code.
Should it become necessary for IBM to make changes to machine code, IBM will make the changes available at the IBM eServer p5 technical support page on ibm.com. If the machine does not function as warranted and your problem can be resolved through your application of machine code changes, you are responsible for downloading and installing the designated machine code changes as IBM specifies. You may request IBM to install machine code changes; however, you may be charged for the installation of such changes.
Educational allowance:
A reduced charge is available to qualified education customers. The
educational allowance may not be added to any other discount or
allowance.
Back to top
|
|
| Prices |
|
The prices provided in this announcement are suggested retail prices for the U.S. only and are provided for your information only. Dealer prices may vary, and prices may also vary by country. Prices are subject to change without notice. For additional information and current prices, contact your local IBM representative.
The following are newly announced features on the specified models of the IBM eServer 9117 machine type:
Feature Purchase
Description number price MMMC(2) CSU
Machine type/model 9117-570
eServer MT 9117 $ 1,000 $146 No
2-Way 1.65 GHz 7830 5,133 146 Yes
POWER5 CUoD Processor Card,
0-Way Active, 8 DDR1 Memory
DIMM Slots
2-Way 1.9 GHz 7832 10,900 183 Yes
POWER5 CUoD Processor Card,
0-Way Active, 8 DDR1 Memory
DIMM Slots
2-Way 1.9 GHz 7833 11,990 183 Yes
POWER5 CUoD Processor Card,
0-Way Active, 8 DDR2 Memory
DIMM Slots
8 DDR1 Memory 7834 1,625 78 Yes
DIMM Slots
One Processor 7897 7,700 129 Yes
Activation for
CUoD Processor
Feature #7830
One Processor 7898 21,800 161 Yes
Activation for
CUoD Processor
Feature #7832
One Processor 7899 23,980 161 Yes
Activation for
CUoD Processor
Feature #7833
One Processor 7929 2,438 78 Yes
Entitlement for
Processor
Feature #7834
On/Off Processor 7951 0 0 Yes
Enablement
On/Off Processor 7952 86 0 Yes
Day Billing
for Feature 7830
On/Off Processor 7953 242 0 Yes
Day Billing
for Feature 7832
On/Off Processor 7955 266 0 Yes
Day Billing
for Feature 7833
30 Days Prepaid 7956 2,567 0 Yes
Reserve Capacity
for 1.65 GHz Processors
30 Days Prepaid 7959 7,267 0 Yes
Reserve Capacity
for 1.9 GHz Processors
Zero-priced Value 8452 0 129 Yes
Pak Processor
Activation Code for #7830
Zero-priced Value 8454 0 161 Yes
Pak Processor
Activation Code for #7832
Zero-priced Value 8455 0 161 Yes
Pak Processor
Activation Code for #7833
Zero-priced Value 8456 0 78 Yes
Pak Processor
Entitlement for #7834
- 2
- Monthly minimum maintenance charge
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
AIX Partition Specify 0265 $ 0 Both Yes No
Linux Partition 0266 0 Both Yes No
Specify
CCS Customer 0986 0 Both Yes No
Service
Specify (U.S.)
RIO-2 Remote 1800 3,000 Both Yes No
I/O Loop Adapter
Operator Panel 1846 150 Both Yes No
Processor Cable, 1847 2,000 Both Yes No
Two-Drawer System
Processor Cable, 1848 7,200 Both Yes No
Three-Drawer System
Processor Cable, 1849 13,500 Both Yes No
Four-Drawer System
SP Flex Cable, 1857 1,000 Both Yes No
Two-Drawer System
SP Flex Cable, 1858 3,000 Both Yes No
Three-Drawer System
SP Flex Cable, 1859 5,600 Both Yes No
Four-Drawer System
PCI SCSI Adapter 2114 225 Both Yes No
16-Bit Differential
External Y Cable
Converter Cable, 2118 50 Both Yes No
VHDCI to P,
Mini-68 pin to
68 pin, 0.3M
0.6M 16-bit 2424 90 Both Yes No
SCSI-2 System to
System Cable
2.5M 16-bit 2425 108 Both Yes No
SCSI-2 System to
System Cable
LC-SC 50 Micron 2456 83 Both Yes No
Fiber Converter
Cable
LC-SC 62.5 Micron 2459 83 Both Yes No
Fiber Converter
Cable
External USB 2591 83 Both Yes No
1.44 MB
Diskette Drive
IDE Slimline 2640 378 Both Yes No
DVD-ROM Drive
2 Port USB 2738 250 Both Yes No
PCI Adapter
POWER GXT135P 2849 412 Both Yes No
Graphics
Accelerator
with Digital
Support
ARTIC960Hx 4-Port 2861 354 Both Yes No
EIA-232 Cable
ARTIC960Hx 4-Port 2863 417 Both Yes No
X.21 Cable
ARTIC960Hx 4-Port 2864 700 Both Yes No
V.35 (DTE) Cable
IBM ARTIC960RxD 2877 25 Both Yes No
Quad DTA, H.100,
4-Drop Cable
Asynchronous 2934 37 Both Yes No
Terminal/Printer
Cable EIA-232
Asynchronous 2936 61 Both Yes No
Cable EIA-232/V.24
8-Port Asynchronous 2943 1,162 Both Yes No
Adapter EIA-232/
RS-422, PCI bus
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
128-Port Asynchronous 2944 $1,079 Both Yes No
Controller,
PCI bus
IBM ARTIC960Hx 2947 3,021 Both Yes No
4-Port
Multiprotocol
PCI Adapter
Cable, V.24 / EIA-232 2951 146 Both Yes No
Cable, V.35 2952 267 Both Yes No
Cable, V.36 / EIA-499 2953 212 Both Yes No
Cable, X.21 2954 146 Both Yes No
2-Port Multiprotocol 2962 1,666 Both Yes No
PCI Adapter
Serial to Serial 3124 67 Both No No
Port Cable for
Drawer/Drawer
Serial to Serial 3125 67 Both No No
Port Cable for
Rack/Rack
RIO-2 (Remote I/O-2) 3146 350 Both Yes No
Cable, 1.2M
RIO-2 (Remote I/O-2) 3147 550 Both Yes No
Cable, 3.5M
RIO-2 (Remote I/O-2) 3148 850 Both Yes No
Cable, 10M
RIO-2 (Remote I/O-2) 3156 400 Both Yes No
Cable, 1.75M
RIO-2 (Remote I/O-2) 3168 450 Both Yes No
Cable, 2.5M
36.4 GB 10,000 rpm 3273 750 Both Yes No
Ultra320 SCSI
Disk Drive Assembly
73.4 GB 10,000 rpm 3274 1,400 Both Yes No
Ultra320 SCSI
Disk Drive Assembly
146.8 GB 10,000 rpm 3275 1,999 Both Yes No
Ultra320 SCSI
Disk Drive Assembly
36.4 GB 15,000 rpm 3277 1,771 Both Yes No
Ultra320 SCSI
Disk Drive Assembly
73.4 GB 15,000 rpm 3278 2,715 Both Yes No
Ultra320 SCSI
Disk Drive Assembly
L200P Flat Panel Monitor 3636 1,645 Both Yes No
IBM T541H/L150p 3637 625 Both Yes No
15-in TFT
Color Monitor
IBM C220p 21-inch 3638 829 Both Yes No
Color Monitor,
Business Black,
and Cable
IBM ThinkVision(TM) L170p 3639 829 Both Yes No
Flat Panel Monitor
Serial Port 3925 21 Both Yes No
Converter Cable,
9-Pin to 25-Pin
Async Printer/ 3926 76 Both Yes No
Terminal Cable,
9-pin to 25-pin, 4M
6 Foot Extender Cable 4242 83 Both Yes No
for Displays (15 pin
D-shell to 15 pin
D-shell)
Extender Cable -- 4256 42 Both Yes No
USB Keyboards, 2M
H-100 Bus 4353 83 Both Yes No
8-position Cable
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
2048 MB (4 x 512 MB) 4452 $ 2,600 Both Yes No
DIMMs, 208-pin,
8NS DDR SDRAM
8192 MB (4 x 2048 MB) 4454 14,746 Both Yes No
DIMMs, 208-pin,
8NS Stacked
DDR SDRAM
4096 MB (4 x 1024 MB) 4490 7,040 Both Yes No
DIMMs, 208-pin,
250 MHz Stacked
DDR1 SDRAM
16384 MB (4 x 4096MB) 4491 51,316 Both Yes No
DIMMs, 208-pin,
250 MHz Stacked
DDR1 SDRAM
32768 MB (4 x 8192MB) 4492 103,000 Both Yes No
DIMMs, 208-pin,
250 MHz Stacked
DDR1 SDRAM
Rack Indicator, Rack #1 4651 0 Both Yes No
Rack Indicator, Rack #2 4652 0 Both Yes No
Rack Indicator, Rack #3 4653 0 Both Yes No
Rack Indicator, Rack #4 4654 0 Both Yes No
Rack Indicator, Rack #5 4655 0 Both Yes No
Rack Indicator, Rack #6 4656 0 Both Yes No
Rack Indicator, Rack #7 4657 0 Both Yes No
Rack Indicator, Rack #8 4658 0 Both Yes No
Rack Indicator, Rack #9 4659 0 Both Yes No
Rack Indicator, Rack #10 4660 0 Both Yes No
Rack Indicator, Rack #11 4661 0 Both Yes No
Rack Indicator, Rack #12 4662 0 Both Yes No
Rack Indicator, Rack #13 4663 0 Both Yes No
Rack Indicator, Rack #14 4664 0 Both Yes No
Rack Indicator, Rack #15 4665 0 Both Yes No
Rack Indicator, Rack #16 4666 0 Both Yes No
Rack Status Beacon 4691 10 Both Yes No
Cable, Junction Box
To Drawer Or
Status Beacon
Rack Status Beacon 4692 10 Both Yes No
Cable, Junction Box
Daisy Chain
Rack Status Beacon 4693 292 Both Yes No
Junction Box
IBM Token-Ring 4959 662 Both Yes No
PCI Adapter
10/100 Mbps 4962 412 Both Yes No
Ethernet PCI
Adapter II
Customer Service 5001 0 Both Yes No
Specify
Software Preinstall 5005 0 Initial
IBM Gigabit 5700 1,416 Both Yes No
Ethernet-SX
PCI-X Adapter
IBM 10/100/1000 5701 1,066 Both Yes No
Base-TX Ethernet
PCI-X Adapter
PCI-X Dual Channel 5703 3,000 Both Yes No
Ultra320 SCSI
RAID Adapter
IBM 2-Port 5706 1,599 Both Yes No
10/100/1000
Base-TX Ethernet
PCI-X Adapter
IBM 2-Port Gigabit 5707 2,124 Both Yes No
Ethernet-SX
PCI-X Adapter
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
Dual Channel 5709 $2,175 Both Yes No
SCSI RAID
Enablement Card
PCI-X Dual Channel 5712 658 Both Yes No
Ultra320
SCSI Adapter
2 Gigabit 5716 2,267 Both Yes No
Fibre Channel
PCI-X Adapter
10 Gigabit 5718 5,000 Both Yes No
Ethernet
PCI-X Adapter
IBM 4.7 GB 5751 1,000 Both Yes No
IDE Slimline
DVD-RAM Drive
Power Control Cable 6001 25 Both Yes No
(SPCN) -- 2 meter
Power Control Cable 6006 40 Both Yes No
(SPCN) -- 3 meter
Power Control Cable 6007 70 Both Yes No
(SPCN) -- 15 meter
Power Control Cable 6008 50 Both Yes No
(SPCN) -- 6 meter
Power Control Cable 6029 90 Both Yes No
(SPCN) -- 30 meter
PCI Universal 6204 541 Both Yes No
Differential
Ultra SCSI Adapter
Power Cable -- 6458 14 Both Yes No
Drawer to IBM PDU,
14-foot, 250V/10A
Power Cord (14-foot), 6469 14 Both Yes No
To Wall, (250V, 15A),
United States,
Plug Type #5
Power Cord (6-foot), 6470 14 Both Yes No
To Wall (125V, 15A),
Plug Type #4
Power Cord (9-foot), 6471 14 Both Yes No
To Wall/OEM PDU,
(125V, 15A),
Plug Type #70
Power Cord (9-foot), 6472 14 Both Yes No
To Wall/OEM PDU,
(250V, 16A),
Plug Type #18
Power Cord (9-foot), 6473 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type 19
Power Cord (9-foot), 6474 14 Both Yes No
To Wall/OEM PDU,
(250V, 13A),
Plug Type #23
Power Cord (9-foot), 6475 14 Both Yes No
To Wall/OEM PDU,
(250V, 16A),
Plug Type #32
Power Cord (9-foot), 6476 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #24
Power Cord (9-foot), 6477 14 Both Yes No
To Wall/OEM PDU,
(250V, 16A),
Plug Type #22
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
Power Cord (9-foot), 6478 $ 14 Both Yes No
To Wall/OEM PDU,
(250V, 16A),
Plug Type #25
Power Cord (9-foot), 6479 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #6
Power Cord (6-foot), 6487 14 Both Yes No
To Wall, (250V, 15A),
United States,
Plug Type #5
Power Cord (9-foot), 6488 40 Both Yes No
To Wall/OEM PDU,
(125V, 15A or 250V,
10A), Plug Type #2
Power Cord (9-foot), 6493 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #62
Power Cord (9-foot), 6494 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #69
Power Cord (9-foot), 6495 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #64
Power Cord (9-foot), 6496 14 Both Yes No
To Wall/OEM PDU,
(250V, 10A),
Plug Type #66
IBM Rack-mount 7164 168 Both Yes No
Drawer Rail Kit
OEM Rack-mount 7165 168 Both Yes No
Drawer Rail Kit
AAP Software 7305 NC Initial
Pre-Install Indicator
Ethernet Cable, 6M, 7801 12 Both Yes No
Hardware Management
Console to System Unit
Ethernet Cable, 15M, 7802 26 Both Yes No
Hardware Management
Console to System Unit
2-Way 1.65 GHz 7830 5,133 Both Yes No
POWER5 CUoD
Processor Card,
0-Way Active,
8 DDR1 Memory
DIMM Slots
2-Way 1.9 GHz 7832 10,900 Both Yes No
POWER5 CUoD
Processor Card,
0-Way Active,
8 DDR1 Memory
DIMM Slots
2-Way 1.9 GHz 7833 11,990 Both Yes No
POWER5 CUoD
Processor Card,
0-Way Active,
8 DDR2 Memory
DIMM Slots
2-Way 1.5 GHz 7834 1,625 Both Yes No
POWER5 Processor
Card, 0-Way Entitled,
8 DDR1 Memory
DIMM Slots
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
PCI Blind Swap 7861 $ 35 Both Yes No
Cassette Kit,
Single Wide Short
Adapters, Type II
PCI Blind Swap 7862 35 Both Yes No
Cassette Kit,
Single Wide Adapters,
Type II
PCI Blind Swap 7863 50 Both Yes No
Cassette Kit,
Double Wide Adapters,
Type II
Processor Enclosure 7865 1,200 Both Yes No
and Backplane
I/O Backplane, 7866 4,100 Both Yes No
6 PCI-X Slots
System Midplane 7867 500 Both No No
Ultra320 SCSI 7868 1,200 Both No No
6-pack Backplane
Media Enclosure 7869 140 Both Yes No
and Backplane
Power Distribution 7870 200 Both No No
Backplane
Processor Power 7875 1,100 Both No No
Regulator
Serial Port 7878 100 Both Yes No
Riser Card
System Drawer 7879 350 Both Yes No
Enclosure
Service Processor 7881 650 Both Yes No
AC Power Supply, 7888 800 Both Yes No
1400 W
8192 MB (4 x 2048 MB) 7890 8,848 Both Yes No
DIMMs, CUoD,
4096 MB Active, DDR1
4096 MB (4 x 1024 MB) 7893 17,600 Both Yes No
DIMMs, 276-pin,
533 MHz DDR2 SDRAM
One Processor Activation 7897 7,700 Both Yes No
for CUoD Processor
Feature #7830
One Processor Activation 7898 21,800 Both Yes No
for CUoD Processor
Feature #7832
One Processor Activation 7899 23,980 Both Yes No
for CUoD Processor
Feature #7833
One Processor Entitlement 7929 2,438 Both Yes No
for Processor
Feature #7834
Advanced POWER 7942 990 Both Yes No
Virtualization
1024 MB Activation 7950 1,475 Both Yes No
for DDR1 Memory
On/Off Processor 7951 0 Both Yes No
Enablement
On/Off Processor 7952 86 Both Yes No
Day Billing for
Feature 7830
On/Off Processor 7953 242 Both Yes No
Day Billing for
Feature 7832
On/Off Memory Enablement 7954 0 Both Yes No
On/Off Processor 7955 266 Both Yes No
Day Billing for
Feature 7833
30 Days Prepaid 7956 2,567 Both Yes No
Reserve Capacity for
1.65 GHz Processors
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
On/Off Memory 7957 $ 16 Both Yes No
1 GB-Day Billing
for DDR1
30 Days Prepaid 7959 7,267 Both Yes No
Reserve Capacity
for 1.9 GHz Processors
128-Port Asynchronous 8131 50 Both Yes No
Controller Cable,
4.5 Meter
128-Port Asynchronous 8132 33 Both Yes No
Controller Cable,
23cm (9-Inch)
RJ-45 to DB-25 8133 100 Both Yes No
Converter Cable
Rack Mountable Remote 8136 2,083 Both Yes No
Asynchronous Node
16-Port EIA-232
Enhanced Remote 8137 1,329 Both Yes No
Asynchronous Node
16-Port EIA-232
Power Cord Carry Over 8430 0 MES Yes No
Indicator, #9800,
Model Conversion Only
Power Cord Carry Over 8431 0 MES Yes No
Indicator, #9802,
Model Conversion Only
Power Cord Carry Over 8432 0 MES Yes No
Indicator, #9820,
Model Conversion Only
Power Cord Carry Over 8433 0 MES Yes No
Indicator, #9821,
Model Conversion Only
Power Cord Carry Over 8434 0 MES Yes No
Indicator, #9825,
Model Conversion Only
Power Cord Carry Over 8435 0 MES Yes No
Indicator, #9827,
Model Conversion Only
Power Cord Carry Over 8436 0 MES Yes No
Indicator, #9828,
Model Conversion Only
Power Cord Carry Over 8437 0 Both Yes No
Indicator, #9829,
Model Conversion Only
Power Cord Carry Over 8438 0 MES Yes No
Indicator, #9830,
Model Conversion Only
Power Cord Carry Over 8439 0 MES Yes No
Indicator, #9831,
Model Conversion Only
Power Cord Carry Over 8440 0 MES Yes No
Indicator, #9833,
Model Conversion Only
Power Cord Carry Over 8441 0 MES Yes No
Indicator, #9834,
Model Conversion Only
Zero-priced Value Pak 8452 0 Both Yes No
Processor Activation
Code for #7830
Zero-priced Value Pak 8454 0 Both Yes No
Processor Activation
Code for #7832
Zero-priced Value Pak 8455 0 Both Yes No
Processor Activation
Code for #7833
Zero-priced Value Pak 8456 0 Both Yes No
Processor Entitlement
for #7834
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
Quiet Touch Keyboard --
USB, Business Black
U.S. English, #103P 8800 $83 Both Yes No
French, #189 8801 83 Both Yes No
Italian, #142 8802 83 Both Yes No
German/Austrian, #129 8803 83 Both Yes No
U.K. English, #166 8804 83 Both Yes No
Spanish, #172 8805 83 Both Yes No
Japanese, #194 8806 83 Both Yes No
Brazilian/ 8807 83 Both Yes No
Portuguese, #275
Canadian French, #058 8808 83 Both Yes No
Belgian/Dutch, #120 8810 83 Both Yes No
Swedish/Finnish, #153 8811 83 Both Yes No
Danish, #159 8812 83 Both Yes No
Bulgarian, #442 8813 83 Both Yes No
Swiss/French/ 8814 83 Both Yes No
German, #150F/G
Norwegian, #155 8816 83 Both Yes No
Dutch, #143 8817 83 Both Yes No
Portuguese, #163 8818 83 Both Yes No
Greek, #319 8819 83 Both Yes No
Hebrew, #212 8820 83 Both Yes No
Hungarian, #208 8821 83 Both Yes No
Polish, #214 8823 83 Both Yes No
Slovakian, #245 8825 83 Both Yes No
Czech, #243 8826 83 Both Yes No
Turkish, #179 8827 83 Both Yes No
LA Spanish, #171 8829 83 Both Yes No
Arabic, #238 8830 83 Both Yes No
Korean, #413 8833 83 Both Yes No
Chinese/U.S., #467 8834 83 Both Yes No
French Canadian, #445 8835 83 Both Yes No
Thai, #191 8836 83 Both Yes No
Russian, #443 8838 83 Both Yes No
Yugoslavian/ 8839 83 Both Yes No
Latin, #105
U.S. English 8840 83 Both Yes No
(EMEA), #103P
Mouse -- 8841 62 Both Yes No
Business Black
with Keyboard
Attachment Cable
Southern Hemisphere 9004 0 Both Yes No
Designator for Monitors
Language Group 9300 NC Initial
Specify --
U.S. English
Reserved Rack Space 9570 NC Initial
Indicator -- 4U
Initial/
Feature Purchase MES/
Description number price Both
Language Group Specify
Dutch 9700 NC Initial
French 9703 NC Initial
German 9704 NC Initial
Polish 9705 NC Initial
Portuguese 9707 NC Initial
Spanish 9708 NC Initial
Italian 9711 NC Initial
Canadian French 9712 NC Initial
Japanese 9714 NC Initial
Traditional 9715 NC Initial
Chinese (Taiwan)
Korean 9716 NC Initial
Turkish 9718 NC Initial
Hungarian 9719 NC Initial
Slovakian 9720 NC Initial
Russian 9721 NC Initial
Simplified 9722 NC Initial
Chinese (PRC)
Czech 9724 NC Initial
Romanian 9725 NC Initial
Slovenian 9727 NC Initial
The following are new features on the 9078-160.
Initial/
Feature Purchase MES/ RP
Description number price Both CSU MES
Machine type/model 9078-160
9117 Type Server 0020 $0 Both No No
Warranty service upgrade
IOR IOR IOR 9 x 5 24 x 7 24 x 7 4-hour same day 2-hour $2,070 $4,074 $6,486
Annual minimum maintenance charges: For ServiceElect (ESA) Maintenance Service Charges, contact IBM Global Services at 888-IBM-4343 (426-4343).
Model conversion purchase prices
From To machine machine type/ type/ Model conversion model model purchase price(3) 7038-6M2 9117-570 $1,000
- 3
- Parts removed or replaced become the property of IBM and must be returned.
IBM Global Financing: IBM Global Financing offers competitive financing to credit-qualified customers to assist them in acquiring IT solutions. Offerings include financing for IT acquisition, including hardware, software, and services, both from IBM and other manufacturers or vendors. Offerings (for all customer segments: small, medium, and large enterprise), rates, terms, and availability can vary by country. Contact your local IBM Global Financing organization or visit the Web at
IBM Global Financing offerings are provided through IBM Credit LLC in the United States and other IBM subsidiaries and divisions worldwide to qualified commercial and government customers. Rates are based on a customer's credit rating, financing terms, offering type, equipment type, and options, and may vary by country. Other restrictions may apply. Rates and offerings are subject to change, extension, or withdrawal without notice.
Financing offering/capabilities: For more financing information, visit
Back to top
|
|
| Order now |
|
To order, contact the Americas Call Centers, your local IBM representative, or your IBM Business Partner.
To identify your local IBM representative or IBM Business Partner, call 800-IBM-4YOU (426-4968).
Phone: 800-IBM-CALL (426-2255)
Fax: 800-2IBM-FAX (242-6329)
Internet: ibm_direct@vnet.ibm.com
Mail: IBM Americas Call Centers
Dept: IBM CALL, 11th Floor
105 Moatfield Drive
North York, Ontario
Canada M3B 3R1
Reference: RE001
The Americas Call Centers, our national direct marketing organization, can add your name to the mailing list for catalogs of IBM products.
Note: Shipments will begin after the planned availability date.
Trademarks
Back to top
Printable version